The technological parameters control method is used to reduce machining deflection errors of cone axis, thus assuring the machining precision.
并用工艺参数控制法减少锥轴的切削变形误差，从而保证加工精度。
The application of brush plating on H-6000-crusher cone axis was introduced, and the process and conditions during brush plating were obtained.
介绍了电刷镀技术在H-6000型破碎机锥形轴修复中的应用，提出了电刷镀修复H-6000型破碎机锥形轴的工艺流程及条件。
The paper analyses the effect of translation and offset angle of the cone axis to shaft one on the gap variation between two ring-button, which position on two cones.
分析了牙轮钻头安装和磨损间隙引起牙轮相对牙爪轴线的平移和倾斜对相邻锥体上球齿间隙的影响，通过计算，当牙轮、牙爪轴线轴向、径向平移使球齿的趋近量有抵消的趋势；
A conic section whose plane is not parallel to the axis base or generatrix of the intersected cone.
圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线。
A series of seismographs are arranged with their direction of vibration along the generators of a cone with vertical axis.
一组地震仪的振动方向是与具有垂直轴的锥体拾震器方向一致的。
The direction of the axis changes gradually so that it traces out a cone in space.
轴的方向逐渐在变，导致了轴的空间描绘出一个圆锥。
If the axis of the cone (cylinder or plane) lies in the plane of the equator the aspect is transverse.
如圆锥(圆柱或平面)轴位于赤道平面内，则成为横轴。
The H-project of a cone whose axis is parallel to V-plane is analysed.
分析了圆锥轴线为正平线时，在水平面投影图中轮廓线的投影。
The right-truncated cone is firstly adopted to approximate metallic wire target with a curvilinear axis and variable radius.
首先引入直截锥体单元来模拟金属线状目标，可对横截面连续变化的导线做精确近似；
When an air jet is allowed to expand freely, the moving air is contained within an imaginary cone whose axis is coincident with that of the air jet.
当一股气流自由膨胀时，运动着的气流构成一个假想的圆锥体，其轴线与气流的轴线相重合。
Bearing inner ring (shaft circle) of the basic cylindrical hole or holes in the internal tapered cylinder or cone in the axis line access.
轴承内圈(轴圈)的基本圆柱孔或圆锥孔的内接圆柱体或内接圆锥体的轴心线。
With side cone the side scattered exposure is decreased, and the distribution becomes complicated with single-peak in the direction perpendicular to the axis.
在有侧向保护器情况下，侧向散射照射量有所减小，在与光轴垂直方向呈中间高两边低的单峰分布。
The chosen vehicles are a blunt bi cone with cruciform flaps and a variable bent axis vehicle.
所研究的气动外形为带控制舵飞行器和可变弯体飞行器。
The chosen vehicles are a blunt bi cone with cruciform flaps and a variable bent axis vehicle.
所研究的气动外形为带控制舵飞行器和可变弯体飞行器。
应用推荐