Based on FEM software ANSYS, the dendrites stress states are computed using the results of the melt flow as computing parameters.
使用有限元软件ANSYS，把熔体流动计算结果作为参数，计算了枝晶的受力状态。
The authors not only presented the results of the investigation about the frequency of vibration and its amplitude of massive arch dam, but also computed its vibration stress.
文中不仅介绍了重力拱坝自振频率与振型分布的研究结果，而且进行了振动应力的计算。
The stress, strain and displacement in pavement structure can be computed by the mechanical analysis program of the multilayer elastic system.
应用多层弹性体系力学分析程序计算路面结构的应力、应变和位移。
The computed results show that the presence of an interphase can have an important influence on the effective property and local stress distribution of the composites.
还将上述方法与均匀界面层模型进行了比较，计算结果表明，界面层的性质对复合材料有效性质和局部应力的分布有着重要影响。
Then, transient response of vertical displacement, vertical stress and pile-soil stress ratio of some nodes in the elastic subgrade are computed in one single load cycle.
采用桩土分析法，计算分析在一个荷载周期内，弹性路基内各研究节点的位移、竖向应力、桩土应力比的瞬态响应。
Pile's capacity is computed, and two modes are adopted to compute pile's additional stress and settlement, the pressure of hitting pile is analyzed.
计算了桩基单桩承载力，用两种方式计算了桩基附加应力和沉降量，并对沉桩动阻力差异原因进行了分析。
Based on this variation of mechanical state at the earthquake fault, the additional stress given rise on its surroundings and the stress change of this process have been computed and analyzed.
计算并分析了震源力学状态这种变化在其周围产生的附加应力场，以及反映这一过程的地应力变化特征。
Thus the bending stress is very easily computed.
因此，极容易计算出其弯曲应力。
Mechanics behaviors of Sutong bridge were computed by this method, and longitudinal stress, transversal stress of plates of the girder and section stress distribution were discussed consequently.
利用该方法对苏通大桥进行整体受力计算，得到钢箱梁板件的横桥向和顺桥向应力，分析了钢箱梁顶板应力在横桥向的不均匀性。
The tooth deformation includes the contact deformation, deflection, base deformation and the influence of the body deformation, and the contact stress and the stress distribution are computed too.
轮齿变形包括轮齿接触、挠曲、基础变形和齿轮本体变形的对它影响，还有接触应力和分布。
In the method the critical sliding surface is found by thinking about the stress moving of damaged points according to strain and stress that is computed by finite-element method.
该方法利用有限元方法计算土体单元的应力应变，根据破坏单元直接确定临界滑裂面。
The maximum operating stress is computed and limited to prevent conditions of ratchet(progressive plastic deformation with cycles), and not to fatigue.
也有一个对最大组合应力的限制，持续负载加上位移应力，以限制渐变。
The stress and temperature distribution were computed by the finite element software ANSYS for the two instances of steady operation and starting-up.
通过有限元软件A NSYS，分别计算了启动和稳态操作情况下， 加氢反应器筒体的温度分布和应力分布。
It is proved that the computed results are in agreement with the experimental results by analysing the residual stress, strain and displacement of gun autofrettage.
通过对身管自紧的残余应力、残余应变及残余位移分析，证明其计算结果与实验结果相当吻合。
The non - linearity of the gasket material was simulated, and the gasket stress and flange stress were computed with the 3D FEM in this paper.
采用有限元法模拟了垫片的非线性特性，计算了垫片应力及法兰应力。
The flow and the shear stress distribution of the channel were computed by limited volume method.
采用有限元分析方法分析通道内的流型和剪切力分布。
Crack top's tension stress and stress intensity factor caused by thermal stress were computed, structural parameters' sensitivity analysis were made as well.
对路面突然降温时的温度场进行了数值模拟，计算了温度应力作用下反射裂缝尖端的拉应力、应力强度因子，并对其进行了参数分析。
Computed examples show that this model can duplicate variant stress-strain behaviors by adjusting its parameters.
多个算例结果表明，调整二元介质模型的参数，可以描述多种类型的。
The stress and displacement of each node and total deformation of pipe string are computed which at different temperatures and pressure work conditions.
计算了管柱在不同温度和压力工况下管柱轴力、各节点应力、位移和整个管柱总变形量。
Stress intensity factors at the craek tips are computed by complex variable functions and perturbation method and formulas are given in power series forms.
采用复变函数及摄动方法，最后以幂级数形式给出应力强度因子的计算公式。
The pressure, stress and moment are computed, analyzed and compared with designed results, and the rationality of design method is confirmed.
通过围岩压力、钢筋受力、弯矩等计算分析，将实测模拟计算结果与设计值进行了比较，得到了设计方法的合理性结论。
The computed results of the transverse distributions of front and back tension stress...
前、后张力横向分布的计算结果与实验结果吻合较好。
Main Outcome Measures: Primarily, the summed stress score, a 17-segment score for stress myocardial perfusion assessed by Tc-99m tetrofosmin single-photon emission computed tomography (SPECT).
主要观察指标：第一为总负荷评分，即使用Tc-99m单光子发射计算体层摄影（SPECT）评估心肌灌注图像的17节段评分。
The residual stress around a coldworked hole is computed with elastoplastic finite element methods of both flow theory and deformation theory.
研究了基于形变理论的金属板料成形快速有限元分析的方法——反向方法 ，并实现了计算程序。
The residual stress around a coldworked hole is computed with elastoplastic finite element methods of both flow theory and deformation theory.
研究了基于形变理论的金属板料成形快速有限元分析的方法——反向方法 ，并实现了计算程序。
应用推荐