This paper proposes a new method, which USES the 4-2 compressor and CLA instead of the traditional adder to improve the transformation speed.
采用一种新颖的实现方法，利用4 - 2压缩器和超前进位加法器来代替传统的加法，提高了运算速度。
The system model comprises the dynamic heat exchanger model based on the lumped parameter method and moving phase boundary method, and the stable flow models of compressor and expansion valve.
系统模型中包含了用集总参数和相移动边界法建立的热交换器动态模型，以及压缩机和膨胀阀的稳态流动模型。
The paper describes the research progress and development on the capacity control method of reciprocating compressor.
介绍了往复压缩机气量调节方法的国内外研究进展和应用实例。
The calculating method of viscous end speed defective value & end width for centrifugal compressor impeller is given.
给出了离心压缩机叶轮粘性尾迹速度亏缺值及尾迹宽度的计算方法。
Meanwhile, the corresponding high cycles fatigue tests on TC4 compressor blades are done to verify the validity of method.
同时，采用TC4压气机叶片进行了相应的高周疲劳试验，验证了方法的正确性。
The research shows that this method can be applied to high pressure compressor vibration monitoring with obtained good.
研究结果表明，该方法可以应用到该高压压气机振动监测中去，并且获得了较好的结果。
Measurement for rotative velocity of full-closed compressor by the method of measuring vibration frequency is discussed.
讨论了用测量振动频率的方法对全封闭式压缩机进行转速的测量。
Fault diagnosis method based on BP neural network is researched for reciprocating compressor valves.
研究了基于BP神经网络的往复压缩机气阀故障诊断方法。
A method of compressor fault diagnosis based on rough set theory is proposed.
论述了将粗集理论应用于压缩机故障诊断的方法。
Fault diagnosis method based on resource limited artificial immune system (RLAIS) is researched for reciprocating compressor valves.
研究了基于资源有限人工免疫系统(RLAIS)的往复压缩机气阀故障诊断方法。
Aimed at the surging existed in centrifugal compressor, this paper analyzes factors for surging and presents control method for anti-surging.
针对离心式压缩机存在喘振的问题，分析影响喘振的因素，介绍抗喘振控制方法。
This paper gives a method for drawing centrifugal compressor impeller by use of microcomputer.
本文给出了一种以微型计算机为工具绘制离心压气机叶轮图形的方法。
To implement stall margin customizing, two-dimensional performance prediction method of axial compressor for stall margin customizing was developed.
为实施裕度定制，本文开发了能够体现裕度定制思想的轴流压气机二维特性预估方法。
Because the traditional design method of axial flow air compressor was not perfect, it made the assembly work at low efficiency.
由于轴流压气机传统的设计方法不完善，使得基于此种方法设计的机组效率低下。
The outlet pressure of the compressor is one of important performance indexes, the routine determination method for the outlet pressure of the compressor is to carry on the nitrogen injection test.
压缩机出口压力是压缩机的重要性能指标之一，常规的确定方法是进行氮气等气体的试注，通过试注结论获取注气压缩机出口压力。
A nonlinear correlation-integral method was employed to analyze static pressure signals along the compressor casing-wall surface.
运用非线性的相关积分方法对压气机机匣壁面沿程静压信号进行了分析。
Research is carried out on weld groove machining technology of cylindrical duct outlet for barrel compressor, the effective method of solving the problem is put forward.
对筒型压缩机的圆柱形出风管焊接坡口加工工艺进行了探讨，提出了解决该问题的有效方法。
The compressor model was based on the steady lumped parameter method.
以稳态集中参数法建立了压缩机模型；
The paper tells of the regulating principle, method, framework and experimental results of the regulating backflow valve for reciprocal compressor.
介绍了活塞式压缩机可调回流气阀的调节原理、方法和调节机构及其实验结果。
This paper puts forward a method for designing the backward swept blades for centrifugal compressor impellers.
本文介绍一种具有后掠叶片的径流式压气机叶轮造型方法。
A method for predicting the off design performance of an axial flow compressor is presented.
本文介绍一种轴流压气机非设计性能的预测方法。
The results show that the combustor temperature calculated by the turbine flow method is more practical than results calculated by the compressor characteristics method.
结果表明：采用涡轮流量法计算某型发动机燃烧室温度的结果比采用压气机特性法得到的计算结果更接近实际结果。
An information fusion method is proposed for the shortcoming of reciprocating compressor gas valve fault diagnosis using single signal in this paper.
针对使用单一信号对往复压缩机气阀故障进行诊断时所存在的不足，提出一种适合气阀故障诊断的信息融合方法。
In this paper, a method to predict compressor rotor weight has been described with a calculation example.
本文针对压气机转子，提出了一种预估其重量的方法，并进行了实例计算，取得了较满意的结果。
Synchronous induction motor, method for making same, and compressor.
同步感应电动机，同步感应电动机的制造方法，压缩机。
Takes the screw type compressor rotor as an example, a calculating method of unknown section profile of spiral surface and its conjugate shape is introduced and practical formulas are given.
以螺杆压缩机转子为例，介绍了未知螺旋面端截面轮廓及其啮合的共轭齿形求法，给出了实用计算公式。
Aiming at solving surge of centrifugal compressor, this paper analyzes the gas equation of compressor and then put forward the control method to eliminate the surge of the centrifugal compressor.
针对离心式压缩机喘振对工程实践的危害及喘振出现的原因，通过对压缩机气体方程的分析，提出消除离心式压缩机喘振的控制方案。
Aiming at solving surge of centrifugal compressor, this paper analyzes the gas equation of compressor and then put forward the control method to eliminate the surge of the centrifugal compressor.
针对离心式压缩机喘振对工程实践的危害及喘振出现的原因，通过对压缩机气体方程的分析，提出消除离心式压缩机喘振的控制方案。
应用推荐