This paper describes the effect of harmonic winding and harmonic compensating error on electrical machines in automatic control system.
介绍了谐波绕组和谐波补偿误差方法对高性能控制电机的作用。
It's important to improve the performance of weapon for compensating the errors of inertial sensors. Identification of error model is the key to compensating errors.
惯性敏感器误差补偿技术对提高武器装备的性能具有重要的意义，而误差补偿的关键在于误差模型的辨识。
The measurement process of the attitude Angle based on single trailing earth horizon sensor is investigated, and an analytical formula of attitude compensating error is obtained.
基于单轨迹地平仪研究了地平仪测量姿态角的过程，得到了解析形式的姿态角误差补偿公式。
A method that measuring angular displacement error, identifying parameters of error model and compensating error automatically was put forward based on inductosyn angular measuring system.
针对感应同步器测角系统，提出了一种自动检测测角误差、辨识误差模型系数和补偿误差的方法。
A sophisticated error handling mechanism that includes handling of compensating transactions in cases where a workflow must be "rolled back" to a specific point.
一种成熟的错误处理机制，包括在出现工作流程“回滚”到特定的点这种情况时要处理的补偿事务。
This text has mainly explained and weighed the working principle of the transducer, the error compensating, the main parameter choosing, and has carried on technological economy analysis.
本文主要阐述了称重传感器的工作原理、误差补偿、主要参数选择。并进行了技术经济性分析。
This paper discusses the design method of signal conditioning circuit and Compensating technology of measuring error in using hardware and software for the pressure sensors.
介绍压力传感器的信号调节电路设计方法和测量误差的软、硬件补偿技术。
Since the electrode material of compensating wire and cable and thermocouple are different, the two contacts at the connection must be at the same temperature to avoid further error.
由于补偿导线和热电偶的热电级材料并不完全相同，所以要求它们连接处两接点温度相同，否则又会引入误差。
The result shows that the new self calibration system has greatly improve the stability of the system and completely achieved goal of compensating system error.
结果表明系统很好的实现了电路设计的目的，达到了补偿系统误差、大大提高系统稳定性的目的。
In the production practice, this problem should be kept in mind and resolved by programming for compensating the variation of tool nose curvature radius and removing the error.
在实际生产中要加以注意，并通过编程以补偿刀尖圆弧半径的变化，消除误差，使问题得以解决。
On-line modeling, forecasting and compensating way for machining error in boring are introduced.
文章介绍了镗削加工误差的在线建模和预报补偿控制方法。
So it is crucial that measuring electrical thickness exactly in order to realize precision compensating electrical thickness error.
因此，准确测量天线罩电厚度是实现电厚度误差高精度补偿修正的关键。
But adopt the single chip microcomputer error compensating system and can compensation back engagement, raising fabrication accuracy.
而采用单片机误差补偿系统可以对背吃刀量进行补偿，提高加工精度。
Also principle of test error reducing by ambient air temperature compensating electrical resistance is expounded.
阐述了环境空气温度补偿电阻减小测量误差的原理。
A single chip computer controlled error compensating system USES digital display of inductosyn to compensate errors of scaled zero position.
介绍一种由单片机控制的误差补偿系统，利用感应同步器数显装置对定尺零位误差进行补偿。
Phase lock loop and benchmark resistance compensating technologies were used to improve the detection precision, the error was less than 10%.
通过锁相放大技术及基准电阻补偿方法提高了测量的精度，误差在10%以内。
And discussing the method compensating position error.
探讨了扫描面位置误差的补偿方法。
In this paper, author studies the position error-compensating control problem of cutting process by using the classical control theory.
本文作者运用经典控制论对切削过程的位置误差补偿控制进行了研究。
An error compensating method is put forward after the UWB transmit-receive 'system error being discussed.
讨论了超宽带收发系统的误差，并提出了收发系统误差的补偿方法。
A neural network model with dynamical compensating capability is analyzed. During the training of this network model, we apply the principle of dynamic error back-propagation.
本文分析了一种动态补偿神经网络模型，模型的训练利用反向传播原理实现。
Estimating and compensating carrier frequency offset are to achieve carrier frequency synchronization. Estimating symbol rate and correcting timing error are used to synchronize symbol.
估计并补偿频偏是为了实现载波同步，估计符号率和校正定时误差是为了实现码元同步。
Bringing these parameters into interpolation error equation, and then errors can be worked out which provides a theoretical basis for error compensating.
将得到的波形参数带入细分误差公式，即可以求取细分误差，并为误差补偿提供了理论基础。
The validity of the method used for choosing optimal temperature measured points, modeling and compensating thermal error of the machine is experimentally confirmed.
应用表明这是一种在机床温度测量、热误差建模及补偿中选择最佳测温点的有效方法。
The invention provides a gas sensor, an air-fuel ratio controller and a transportation device for simply compensating the resistance error of the heater.
本发明提供可以正确且简便地补偿加热器的电阻值误差的气体传感 器、空燃比控制装置以及运输设备。
The test for compensating of the sight line error for missile radome has been done by the semi-real simulation system, which shows the highly precise compensation for missile homing.
利用射频仿真系统对该补偿系统进行动态实物联试，试验表明该补偿系统达到了很高的补偿精度。
The compensating method for MEMS gyroscope random drift error is discussed.
从工程实用的角度出发，探讨了MEMS陀螺仪随机漂移误差的有效补偿方法。
Compensating reactor in a Capacitive Voltage Transformer (CVT) influences not on-ly its ratio error, but also the rated output capacity.
电容式电压互感器(CVT)的补偿电抗器不但影响电压比的准确度，而且还影响它的额定容量。
A method for compensating the measuring error of the grating displacement measurement system with absolute zero mark is presented.
提出一种具有绝对零位标识的光栅位移测量系统的误差补偿方法。
A method for compensating the measuring error of the grating displacement measurement system with absolute zero mark is presented.
提出一种具有绝对零位标识的光栅位移测量系统的误差补偿方法。
应用推荐