In China, an international communication program was started to send support to other countries.
在中国，一个国际交流项目已经启动，向其他国家提供支持。
The flowchart of communication program is also given in this paper.
文章给出了通信程序的流程图。
The data communication program between stations and the laser range finder was written.
编制了测量站点和激光测距仪之间的数据通讯软件。
It is helpful to the designer of serial interface communication program of the real time clock device.
该方法对于实时时钟器件串行接口通信程序的设计具有一定的借鉴作用。
Mobile station, base station, mobile communication system, mobile communication and mobile communication program.
移动台，基站，移动通信系统，移动通信与移动通信程序。
The final part introduces the programming method to network communication program.
最后一部分简单介绍了网络通信程序的编写方法。
At last, the communication program applied in Master-Slave control system base on MODBUS protocol is designed.
最后设计应用于主从式控制系统的通讯程序，这个程序是基于MODBUS协议的。
Network communication program of DNC communication platform and communication of serial port server is developed.
开发了DNC通讯平台的网络通信程序和串口服务器的通信程序。
The paper also expounded designing communication program of the system and multi-thread technology used by the system.
并对系统的通信程序设计及系统所采用的多线程技术作了阐述。
The main contents are: writing data communication program to connect math models with virtual DCS based on database technology;
主要内容有：利用数据库技术编制数学模型和虚拟DCS之间的数据通信接口；
DSP based F28335 AD2S1210 serial communication program, the use of software simulation SPI interface for communication, tested available.
基于DSP F28335的AD2S1210的串行通信程序，采用软件模拟SPI接口进行通信，经测试可用。
The communication program can read or write each soft device inside FX series PLC, and allow individual bit images to be forced on or OFF.
该通信程序能读写FX全系列PLC内部各种软设备，强制复位与置位位映象元件。
Information communication system, information processing apparatus, information communication program, and information communication method.
信息通信系统，信息处理设备，信息通信程序和信息通信方法。
The communication program used for communication between pocket computer and instrument with HART protocol and its programming are introduced.
介绍了用于掌上电脑与HART协议仪表进行通信的通信程序及其编制方法。
The data acquisition system with communication function and the communication program design are introduced with parts of the flow charts given.
本文介绍了具有通信功能的数据采集系统，并重点介绍了通信程序设计，给出了部分程序框图。
Program of Software mainly include acoustic communication program, UART program, CAN program, data acquisition and processing program and so on.
软件程序主要包括水声通讯程序、UART串口程序、CAN通讯程序和数据采集处理程序等。
On the basis of analyzing the data of the internal communications of the device, the communication program both the master and the slave is given.
在分析本装置内部通信数据的基础上，分别给出了主机和从机的通信程序。
The characteristics of the architecture are studied. Its application in the motor control and CAN bus communication program is discussed in detail.
研究了三层抽象软件体系结构的特点，并详细论述了该结构在电机控制以及CAN总线通信程序设计中的具体应用。
There are system administrative program, man-machine interface program, fuzzy algorithm program, PID algorithm program and communication program etc.
程序模块主要有：系统管理程序，人机界面交互接口程序，模糊算法程序，PID算法程序和串口通信程序等。
In the software design part, the design includes a gyro stabilization program, the sensor signal processing program, and serial communication program.
在软件设计部分，设计包括陀螺稳定程序、传感器信号处理程序和串口通信程序。
This paper provides the CAN bus communication program of intelligent instrument system based on the analysis of the characteristics of the fieldbus CAN.
在分析了CAN现场总线特点的基础上提出了智能测控仪表系统的CAN总线通信方案。
The software design include the serial port communication program design, stepper motors velocity curve control and the data acquisition program design.
在下位机软件设计中介绍了串口通信程序设计、步进电机速度曲线的控制和数据采集程序设计。
The IPC-based control software consists of man-machine interface application program, communication program between IPC and PMAC, motion programs and PLC programs.
基于ipc机的控制软件主要包括四个部分：人机界面应用程序、上下位机通讯程序、运动程序和plc程序。
This article analyzes three methods of realizing serial communication program automation, including software polling, communication event and multithread in details.
详细分析了实现串行通讯程序自动化的三种方法：软件查询、通讯事件和多线程。
It lays stress on the design of communication protocol, the initial setting of PC's, PLC's and microprocessor's communication program and some program flow concerned.
着重介绍了通信协议的设计及PC机、PLC和单片机的通信程序初始设置和相关的程序流程。
The experience of designing the serial communication program between PC and 89c51 micro-controller for the speed control of large DC motor is introduced by some examples.
通过实例，介绍为大型直流电机调速系统开发PC机与89c51芯片之间串行数据通信的经验。
This paper expounded that the long distance operating station connect to PLC control system with ASCII module, and edited the communication program stored in ASCII module.
本文阐述了可编程控制器控制系统中，通过ASCII模块，实现远程操作站与可编程控制器的连接，并开发了ASCII模块中的接口通讯程序。
The ac traction control software and communication program completed their tasks in experiment, and the simulant and experimental system of the ac traction was in better control.
经过实验运行，交流牵引控制软件和通信程序实现了本课题需要完成的任务，交流牵引模拟实验系统得到了很好的控制。
In addition, the hardware of numerical control lens-edger is designed. The USB module is also developed and two methods for the design of USB communication program are introduced.
此外，设计了数控镜片磨边机的硬件电路，完成了磨边系统usb数据通信模块的设计，并给出两种USB通信程序的设计方法。
In addition, the hardware of numerical control lens-edger is designed. The USB module is also developed and two methods for the design of USB communication program are introduced.
此外，设计了数控镜片磨边机的硬件电路，完成了磨边系统usb数据通信模块的设计，并给出两种USB通信程序的设计方法。
应用推荐