With these parameters, the SCSI command could be sent to the target device.
有了这些参数之后，就可以将SCSI命令发送到目标设备。
This shortcut would actually only run the emulator in Command Prompt and not load an actual virtual device.
这个快捷方式实际仅在命令提示符的模拟器中运行，不能在一个实际的虚拟设备中加载。
The fourth command creates a domain object for each device in the managed set (there is currently only one) and assigns the configuration source for this domain to the URL shown.
第四个命令为管理集（通常只有一个）中的每一个设备创建一个域对象，然后将这个域的配置资源指定到显示的URL。
A GPRS device, which resembles a modem with an extended at command set, must define a context using an at command before it enters data mode.
GPRS设备类似于拥有扩展AT命令集的调制解调器，在进入数据模式之前必须使用AT命令定义一个上下文。
An initiator sends a command request to a target device.
发起者向目标设备发送命令请求。
"The scan script sends the public password for the product, and if the device responds with the 'command prompt' for that product interface, then the machine is obviously open," Stolfo said.
斯多夫说：“扫描程序脚本向这些网络设备发送对应厂商的公共密码，如果设备对“命令提示”做出与之对应的响应，那么很明显这台设备是不设防的。”
In addition, detailed command information is needed for the device to fulfill a specific task.
另外，设备要完成具体任务需要详细的命令信息。
Using the following command to check the ID for your root file system device with the device UUID you get from step 1.
使用以下命令检查带有从第1步中得到的设备UUID的根文件系统设备的ID。
The first command creates a Device object in the Manager.
第一个命令在Manager中创建一个Device 设备。
A new ioctl command should be added to the device driver to control the interrupt simulation from the test application.
ioctl命令应该添加到设备驱动程序中，这样就可以从测试应用程序中控制对中断的模拟了。
Use the dd command to simply zero out the entire device (see Listing 6).
使用dd命令将整个设备清零(参见清单6)。
When adding a common paging space device using the chhwres command, you only need to specify one paging VIOS partition.
在使用chhwres命令添加共用分页空间设备时，只需要指定一个分页VIOS分区。
reserve : This command is issued by a host bus adapter to obtain or maintain ownership of a SCSI device.
reserve（占用） :这个命令由总线适配器发送用以获得或保留对SCSI设备的所有权。
An initiator identifies the device type through the inquiry command.
发起者通过inquiry命令识别设备类型。
The third command adds the device to the managed set. A device must be managed in order for the manager to deploy a domain to it.
第三个命令是向管理集中添加设备。
So, you will have to delete both interfaces using the rmdev -dl -r command, re-detect the correct device using CFGMGR, and then set an IP address.
因此，您不得不使用rmdev—dl- r命令删除所有接口，使用cfgmgr重新检测正确的设备，然后设置一个IP地址。
The basic form of the mount command takes two parameters: the device (or other resource) containing the filesystem to be mounted, and the mount point.
mount命令的基本格式有两个参数：含有将要安装的文件系统的设备(或其他资源)和挂载点。
In the output from our lsdev command, you can see that the link aggregation device (ent10 - ent12) looks like a physical adapter.
在lsdev命令的输出中，可以看到链路聚合设备(ent10-ent12)就像是一个物理适配器。
Check your device list with the lsdev command.
用lsdev命令检查设备列表。
With the second chhwres command, add a paging space device to the Shared memory pool.
第二个chhwres命令在共享内存池中添加分页空间设备。
In AIX, the cfgmgr command detects any hardware devices present on the system and even tells you which device drivers may be missing.
在AIX 中，cfgmgr命令会检测系统中所有的硬件设备，甚至会告诉您丢失了哪些设备驱动程序。
You can confirm the existence of this device with the lsdev command on the VIOS.
可以在VIOS上使用lsdev命令检查是否存在此设备。
After you select the View command, the file will be downloaded and displayed on the device, as shown on the right screen shot in Figure 5.
选择了View命令后，就会下载这个文件并显示在设备上，如图5右边的屏幕快照所示。
This can also happen when the VM system is shutdown with the SHUTDOWN command, which is not an issue for a Linux swap device.
这在VM系统使用COMMAND命令关闭时也会发生，而Linux交换设备则不存在这种问题。
Use the blkid command to find out the UUID and label (if present) associated with a device.
使用blkid命令来寻找设备相关的UUID和标签(如果有)。
Although the ifconfig command can handle some temporary device configuration changes, these changes will not be registered permanently unless you use the chdev command.
尽管ifconfig命令可以处理一些临时的设备配置修改，但是如果不使用chdev命令，这些修改不会永久地注册。
You can solve this problem by typing sync on the command line, forcing any cached data to be immediately written to the device, but this won't solve the unmountable problem.
你可以通过在命令行键入sync解决此问题，这将迫使任何缓存的数据立刻写入该设备，但这仍不能解决无法载载的问题。
The second command shows that you cannot directly query the underlying device by using the standard fuser options.
第二个命令表明，不能使用标准的fuser选项直接查询底层设备。
And while a traditional ramdisk is a block device and requires a MKFS command of some kind before you can actually use it, TMPFS is a filesystem, not a block device; you just mount it, and it's there.
而且传统的虚拟磁盘是个块设备，并需要一个mkfs之类的命令才能真正地使用它，tmpfs是一个文件系统，而不是块设备；您只是安装它，它就可以使用了。
Busy: This command reports back the portion of time that the device was busy servicing transfer requests.
busy：这个命令可以报告该设备忙于处理传输请求的时间比例。
应用推荐