The construction of cold casting heading anchor is introduced, and the main technology requirements of the construction are given.
介绍冷铸镦头锚的构造，给出了主要技术要求。
Form and dimension may also be achieved by a number of alternative processes such as hot or cold extrusion, sand casting, die casting, and precision casting.
形式和尺寸也可以通过其它一些可选工艺来达到，比如热挤出或冷挤出加工，沙模铸造，拉模铸造，或精密铸造。
By using metal mold casting, we can control mold temperature, infusing temperature, infusing speed to avoid defects of pore, cold partition, shrink and loose.
采用金属型立式浇铸，严格控制铸造工艺参数(模具温度、浇注温度、浇注速度)，以避免气孔、缩松、冷隔等缺陷的产生。
The paper discussed the cause of cold model vibration in centrifugal casting, and provided the methods to reduce and avoid the vibration.
本文探讨了冷型在离心铸造过程中产生振动的原因，提出了减小和防止冷型在离心过程中振动的方法。
Studied the annealing institution of 3003-o aluminum alloy strip for drawing is researched, while the chemical composition and casting, hot rolling, the cold rolling, process were determined.
研究了深冲用3003-o铝合金带材合理的生产工艺，在化学成分和铸造、热轧、冷轧工艺确定的情况下，试验研究成品退火工艺制度。
Cold shots develop from low casting temperature, and dirt spots result from pickup of sand or slag by molten metal.
较低的铸造温度会形成冷疤，熔化金属出现的沙粒或炉渣的累积会导致污点。
Properties of the green sand and the surface quality of the casting may be decreased due to the resin sand of cold box cores entering the green sand system.
冷芯盒树脂砂进入湿型砂系统会使湿型砂性能和铸件表面质量下降。
The fan component is produced using cold chamber pressure die casting process.
风机部件的创造采用冷腔室压力拉模铸造工艺。
A new die-casting die fit on cold chamber die casting machine was redesigned in the part of the center gate and floating flow-distribution.
分析了录音机芯飞轮压铸模的原设计失败的原因，重新设计了用于冷室压铸机的中心浇口、浮动分流的压铸模。
Three heat transfer mathematical models are given based on working condition of horizontal cold chamber die casting machine.
针对卧式冷室压铸机压室的工作环境，提出三种不同的热传递数学模型。
Simulation results show a smooth filling, uniform temperature distribution and few flaws such as gas inclusion and cold shut. A casting with a good quality was obtained.
模拟结果表明，该浇注系统填充过程平稳，温度场分布均匀，所得压铸件气体夹杂和冷隔缺陷少，整体质量较高。
The utility model relates to a cold type box for a roll, which is used in industry of manufacturing rolling steel, in particular to the cold type box for a casting roll with a pass.
本实用新型涉及一种制作轧钢工业上使用的轧辊用冷型箱，特别是带孔型铸造轧辊用的冷型箱。
Rapid, low-cost developed samples, including stamping, casting, injection molded parts, pieces of cold heading, Sheet Metal Parts.
快速，低成本试制样品，包括冲压件，铸件，注塑件，冷镦件，板金件。
By 1920, the earliest cold chamber die casting machine was published.
进入20世纪以后，热室压铸机日渐成熟，冷室压铸机问世。
The broken chilling layer emerging in the course of filling molten metal in the cold-chamber sleeve and its effect on casting quality are analyzed.
研究了卧式冷空压铸机压室内金属液充填过程中产生的破碎激冷层及其对待件质量的影响；
Cold Snap: This talent will now always clear the cooldown for Frost Ward, even if the cooldown was triggered by casting Fire Ward.
急速冷却-该天赋将重置冰霜防护结界的冷却时间，即使这个冷却时间是由施放火焰防护结界导致的。
Research and development of mould powder for low carbon steel thin slab casting specially used in cold rolling at TISCO is introduced.
介绍了唐钢薄板坯连铸低碳冷轧用钢保护渣的研究开发过程。
This paper describes the production condition of cold rolled deep drawing quality steel (IF steel) by thin slab continuous casting and rolling technique in Bengang.
介绍了本钢薄板坯连铸连轧工艺生产冷轧深冲钢(IF钢)的情况。
Standard of equivalence of armor plate of the aluminous material of metallic stuff die-casting of water heater, cathode copper, cold rolling, galvanization armor plate has litres bigger.
热水器的金属材料压铸铝材、电解铜、冷轧钢板、镀锌钢板等价格都有较大升幅。
The Primary causes inducing the hot and cold cracks of electric power fitting products of malleable cast iron in casting process are analyzed and discussed.
分析和探讨可铸铁电力金具在铸造生产中，产生热裂和冷裂的原因；
Suitable for metallic and sand casting, also for cold chamber casting;
适用于金属型、砂型铸造，也可冷室压铸。
The primary requirement of cold-rolling feeds, and the equipment design, production management and material flow of thin slab continuous casting and rolling, were investigated in the paper.
本文通过分析冷轧基料的一般要求、薄板坯连铸连轧工艺的设备配置、生产组织和物流衔接，提出了薄板坯连铸连轧工艺大规模生产冷轧基料的具体措施和建议。
Head-cylinder and Intake of non-Ferrous metal, Pouring machine for gravity die, Cold-box machine, Core-Shooting machine, Casting Mold, Exports'casting etc.
轿东发动机缸盖、进气管、冷芯机、射芯机、铸造模具、出口铸件等。
In order to improve the cold fatigue, hot fatigue and mechanical fatigue resisting performance of the moving blade, grain refinement is required for the casting surface.
为了提高动叶片的抗冷热疲劳和抗机械疲劳的性能，铸件表面需进行晶粒细化。
Caster is the equipment that casting and rolling the AI. liquid to supply material for cold mill. it includes horizontal one and slanting one.
铝连续铸轧机是将铝液连铸连轧成供冷轧机轧制用板带坯料的设备，分水平式和倾斜式两种形式。
Mould temperature control is too low will affect liquid aluminum liquidity and cause a casting cold-lap.
模具温度控制过低会影响铝液的流动性并引起铸件冷隔。
The position of overflow and thicker inner gate was optimized to reduce the probabilities of cold shut, flow marks and slag. Furthermore, the surface quality of the die casting improves.
提出了在恰当位置设置溢流槽和增大内浇口厚度等改进措施，从而有效降低了铸件冷隔、流痕、夹渣等缺陷的产生，提高了压铸件表面质量。
The position of overflow and thicker inner gate was optimized to reduce the probabilities of cold shut, flow marks and slag. Furthermore, the surface quality of the die casting improves.
提出了在恰当位置设置溢流槽和增大内浇口厚度等改进措施，从而有效降低了铸件冷隔、流痕、夹渣等缺陷的产生，提高了压铸件表面质量。
应用推荐