Click Test a Login to display a panel similar to Figure 9.
单击testaLogin以显示与图9所示类似的面板。
Click Test a Login to display the panel shown in Figure 9.
单击testaLogin以显示如图9中所示的面板。
Click Test connection to ensure that the values are correct.
单击testconnection以确保那些值是正确的。
Click Test connection to make sure that the connection works.
点击TestConnection确保连接工作正常。
Select a data source, and then click Test Connection. See figure 10.
选择一个数据源，然后单击testConnection，见图10。
Remember to click Test connection to verify your inputs (Figure 15).
记住点击Testconnection以验证您的输入（图15）。
Click Test connection to see if a connection can be established.
单击testConnection，看看连接是否建立了。
Validate the Settings: click Test connection on the bottom of the page.
检验设置：点击页面下部的Testconnection。
Click Test again, and you should get the response shown in Figure 3.
再次点击Test，您应该获取如图3所显示的回应。
After configuration, click Test Connection to ensure that the changes have taken effect.
完成配置后，单击TestConnection以确保修改生效。
Open the publisher assembly diagram, right-click in the diagram and click Test Module.
打开发布者组装关系图，右键单击该关系图并单击TestModule。
When the message displays confirming that the database has been started, click Test Connection.
当确认数据库已经启动的消息显示时，单击TestConnection。
Enter the database host name, the port number, and the database name, and then click Test connection.
输入数据库主机名称、端口号和数据库名称，然后单击test connection。
The signal quality is still low. Move the receiver closer to the wireless mouse, and then click Test Again.
信号质量仍然较低。请将接收器移动到距离无线鼠标较近的位置，然后单击“ 再次测试”。
The signal quality is still low. Move the receiver closer to the wireless keyboard, and then click Test Again.
信号质量仍然较低。请将接收器移动到距离无线键盘较近的位置，然后单击“再次测试”。
Verify that the Derby network database is running, then select the Order DS data source and click Test Connection (Figure 23).
确认Derby网络数据库正在运行，然后选择OrderDS数据源，并单击TestConnection(图23)。
No signal quality information was received. Move the receiver closer to your wireless keyboard, and then click Test Again.
未接收到信号质量信息。请将接收器移动到距离无线键盘较近的位置，然后单击“ 再次测试”。
The signal quality is still low. Try refreshing your connection again by pressing the button on the bottom of the wireless mouse, and then click Test Again.
信号质量仍然较低。按下无线鼠标底部的按钮尝试再次刷新连接，然后单击“ 再次测试”。
In test dialog, select the sample XML document to be shredded for testing and select from the validation drop-down menu whether DB2 is to validate the XML document or not, and then click test.
在Test对话框中，选择测试中要分解的示例XML文档，再从validation下拉菜单中选择DB 2是否验证XML文档，然后单击test。
Click OK and save your test plan.
点击OK并保存您的测试计划。
Click on the manual test case link first.
首先点击手动测试用例连接。
Click through each test to see the specific results of each of these scenarios.
单击每个测试以查看每个场景的具体结果。
Specify the account ID and password you'll use to test, then click OK.
指定您将用于测试的帐户ID和密码，然后单击ok。
If you'd like to take this test online, click here.
如果你想参与在线测试，请按此。
Use any (non-null) value for user ID and password, and click the Test Connection button.
使用任意（非空）值作为用户ID和密码，并单击TestConnection按钮。
In order to check the output of each step, you can click the Test Data TAB of the respective step.
为了检查每一个步骤的输出，您可以单击各自步骤的Testdata选项卡。
Click Finish to test the statement.
单击Finish来测试语句。
On the left of the dialog, expand Business integration and click integration Test Client.
在对话框左边，展开Businessintegration并单击integrationTestClient。
To start the test, click Continue.
要开始测试，请单击Continue。
In the Test window, click the Run Test button.
在Test窗口中，请单击Run Test按钮。
应用推荐