Under system variables section, click path, click Edit.
在系统变量部分，单击路径，单击编辑。
Activate pen tool. Click path to add two points on each corner. See picture below for its placement.
激活钢笔工具。点击路径增加的两点在每一个角落。见图讨论将它放置。
This leads to the problem that users that need access to "poorly positioned" content must click through a long path to navigate, and they have to do this over and over again.
这可导致以下问题：需要访问“极难定位”内容的用户必须从头到尾单击一遍很长的导航路径，并且必须一次又一次地执行此操作。
If no event handlers processed the click, the event will travel back up the same path until it comes back to the root element, where the default click handler will ignore it.
如果没有事件处理程序处理这个单击事件，它就会沿着同样的路线再返回到根元素，这时根元素默认的单击处理程序将忽略该事件。
Enter the path and name of LTPA key file, and then click OK.
输入ltpa密钥文件的路径和名称，然后单击ok。
Select the projects you want on the build path, then click OK.
在构建路径中选择项目，然后单击ok。
Click OK to accept the changes you just made to your project's build path.
单击ok接受对项目的构建路径所做的更改。
Click the OK button to accept the path.
单击ok按钮接受路径。
Click Next after determining the installation path.
在确定安装路径之后单击Next。
You can also click Tab at an empty prompt to see all applications in your PATH.
在空提示行上按tab，就会看到PATH中的所有应用程序。
When the build path looks like this, click ok to apply it to the project.
当构建路径与下图所示差不多时，单击OK将它应用到工程。
If you are prompted to change the auto launch configuration to your workspace path, click Yes.
如果你被提示将自动启动配置更改为你的工作空间路径，点击Yes。
Specify the path as c:/Mytestfile.txt. Click OK to Save.
指定路径为c:/Mytestfile.txt，单击OK保存。
After entering the project path, click Next.
在输入项目路径以后，点击Next。
On the right side of the editor, click the browse or ellipses (...) button next to the Source path field.
在编辑器的右边，点击Source路径区域附近的浏览器或者省略号(…)按钮。
Click Add and fill in the path (eg. e: \ TMP).
单击add并填写路径(比如e： \tmp)。
Select the installation path, and click next.
选择安装路径并单击next。
Provide the full path to the disks and then click Next.
提供磁盘的完整路径，然后单击Next。
Provide the full path to the disks, and click Next, as shown in Figure 12.
输入磁盘的完整路径，然后单击Next，如图 12 所示。
If you see a warning notifying you of path link problems, click Yes.
如果您遇到向您通知路径链接问题的警告，则单击yes。
To add projects in the same workspace as your build path, click the projects TAB, then click add.
要将项目添加到构建路径所在的工作空间中，单击projects选项卡，然后单击add。
Pick the Direct Selection Tool and click on the shape path. Click the vertical point and drag it down while holding the Shift key until it reaches the same level with the horizontal axis.
用直接选取工具单击这个图形的路径，单击垂直点然后按住shif t键往下拉直到如图所示状态。现在看起来不错了，但是还是比较简陋。
On the Export dialog box, in the Destination field, enter an.ear file path and name, and then click Finish.
在Export对话框上，在Destination字段中，输入.ear文件路径和名称，然后单击Finish。
Browse to the (installdir) \ webcontent path and click next.
浏览到(installdir) \webcontent路径并单击Next。
Browse to the (installdir) \ ControllerProxyServer path and click next.
浏览到(installdir) \ControllerProxyServer路径并单击Next。
In the Archive text box, enter the path to the generated ticker.war and click Install.
在Archive文本框中，输入所生成ticker . war的路径，并单击Install。
Click on Add, enter a sensible name as the alias, and put the full path to where you copied the file, then click OK.
单击add，输入合理的名称作为别名并给出复制文件的完全路径，然后单击ok。
For consistency, click use recommended path for each artifact, and the tool fills in the path.
为了一致性，请对每个工件单击userecommendedpath，工具将会填充路径。
Enter the path where you installed Notes for the value, and then click OK. This path should not have any Spaces in it.
在value栏输入Notes的安装路径，然后单击ok。
Click on the path shown for resource Paths, and then add the following to the end of the path: \ resources.
单击为resourcePaths显示的路径，然后将\resources添加到路径结尾处。
应用推荐