The features of digital circuit signal are simply analyzed.
浅析数字电路信号特点。
Open-circuit signal line may be subject to interference arising from the incorrect output.
开路的信号线可能会受到干扰而产生不正确的输出。
Comparing with the digital circuit, analog circuit signal has a wide dynamic range and varied waveform changes, Therefore, they fault detection has been the focus studied.
相对于数字电路，模拟电路的信号动态范围宽、波形变化大，因此对其的故障检测一直是研究的重点。
The probability and advantage of the short circuit signal detection of CO_2 welding system by wavelet were tested theoretically, which is the theoretical foundation of the DSP system.
首先从理论上验证利用小波变换检测短路信号的可行性和其优越性，为基于小波变换的CO_2焊短路信号DSP检测系统建立了理论基础。
With the circuit schematic design and the high-speed PCB design, completes stackup design and high-speed signal line design.
通过电路原理图设计和高速PCB 设计，完成了堆叠设计和高速信号线设计。
You can build a circuit that generates a CSYNC signal for CARDS that don't do this already (see Resources), but it is generally easier to just purchase a card that already generates it.
对于那些没有CSYNC信号的显卡来说，可以设计一个生成CSYNC信号的电路(请参阅参考资料)，但是通常购买一个具有这种信号的显卡更加容易。
With two diodes in parallel back to back, the circuit will provide protection regardless of the signal polarity.
由于两个二极管反向并联，所以此电路能够对任何极性的信号进行保护。
This paper analyzes reason of measure waveform produce error in decode circuit, put forward experiment means of adopt closed circuit television system transmit signal.
分析了在解码电路实验中，测量波形产生误差的原因，提出了采用有线电视系统传送信号的实验方法。
The digital realization of monostable circuit and extraction of bit-synchronous signal with digital phase lock loop are also introduced in detail.
对于其中的单稳态电路的数字化和数字锁相环提取位同步信号也进行了详细的设计说明。
The power supply circuit, driving circuit, display circuit, software design and signal collection of the control system are outlined.
概述了控制系统的电源电路、驱动电路、显示电路与软件设计及信号采集的方法。
The design method, debug method and the method of enhancing degree of linearity are researched in the constituting of analog signal isolating circuit with linear optical couplers.
研究了应用线性光耦合器组成模拟信号隔离电路的设计方法、调试方法以及提高线性度的方法。
For AC voltage measurement, an RMS converter circuit or a precision rectifier circuit convert the AC signal into a DC voltage.
对于交流电压测量﹐利用有效值转换电路或精密整流器电路将交流信号转换成直流电压。
Design the signal adjust circuit for sensor, and the power amplification circuit for the hydraulic pressure system of test platform and the controller of magnetorheological dampers.
设计出传感器输入输出信号调理电路和试验台架液压激振系统、磁流变阻尼器控制器的功率放大电路。
This article introduces the work principle of untouched electrode method exploration, wave of transmit signal needed in exploration and circuit that generate transmit signal.
本文介绍了不接触电极法测量的工作原理，测量中所需的发射信号的波形以及产生发射信号的电路。
Sensor module is composed of sensor circuit, modulation circuit and analog signal switch.
传感模块由传感器电路、调制电路和模拟信号开关组成。
Moreover, the potential control circuit and signal measuring circuit are designed and applied in controlling potential and processing the output signal of the sensor.
此外，设计并应用了电位控制和测量电路，实现了对传感器的电位控制以及输出信号的处理。
This paper adopts harmonic choice method to design fluxgate signal processing circuit in allusion to the environment magnetic field strength signal of fluxgate sensor detecting.
针对磁通门传感器检测到的环境磁场强度信号，运用谐波选择法，设计了磁通门信号处理电路。
According to the principle of view the Doppler frequency detection, the detector makes up of the transmitter, the transfer circuit, receiver and signal processing circuit.
根据多卜勒频偏检测原理，该探测器由发射机、转换电路、接收机和信号处理电路构成，发射信号是设计的关键。
It also conducts the signal (it doesn't conduct DC), and is often used at other points in a circuit where the signal needs to travel between two different DC voltages.
同时它也能引导信号(但不引导直流电)，它也经常被用在电路里的信号需要跨越两个不同直流电压之间的地方。
The differential signal is the spike pulse signal that is produced by differential circuit. Original differential circuit is very difficult to obtain the ideal differential signal.
微分信号是由微分电路产生的一种“尖峰”脉冲信号，原来的微分电路很难获得理想的微分信号。
This system is constituted with the optical fiber sensor, signal detection electric circuit, single chip processing circuit and display unit.
该系统由光纤传感器、信号检测电路、单片机处理电路和显示装置组成。
This paper introduces signal switchover circuit that transforms voltage signal to current signal in order to improve signal reliability.
介绍一种旨在提高信号传输可靠性而设计的信号转换电路，它将电压信号变换成电流信号进行传输。
Traditional fluxgate adopts analog circuit to process its output signal.
传统磁通门传感器主要采用模拟电路进行信号处理。
Based on this mathematics model, the optimum signal-processing circuit, having high reliability and high stability, is designed and applied to the automatic measurement system of the focusing units.
基于该数学模型，优化设计了高可靠性、高稳定性的信号调理电路，并在聚焦元件自动测量系统中得到了实际应用。
Details of the sensor's structure, its working principle, the selection of working mode as well as the signal processing circuit is presented.
详细介绍了传感器的结构、工作原理、工作模式的选择以及信号检测电路。
Details of the sensor's structure, its working principle, the selection of working mode as well as the signal processing circuit is presented.
详细介绍了传感器的结构、工作原理、工作模式的选择以及信号检测电路。
应用推荐