The digital input provides the load required for the circuit to work.
数字输入为此电路提供负载。
This simple circuit made up of a source, a load and two wires is seldom, if ever, met with in practice.
这种由一个电源、一个负载和两根导线组成的简单电路，在实际中即使能碰见也是很少的。
With short circuit protection, over current protection, the load voltage protection protection and multiple protection.
具有短路保护、过电流保护、过负载保护以及电压保护多重保护。
Purpose: it can be used as shunt and load resistor in DC or ac circuit of electric facility and electron instrument widely.
用途：可广泛用于各种电气设备和电子仪器的直流或交流电路中作分流或负载电阻等。
This paper introduces a design method and circuit of power supply with high voltage and high frequency response for driving capacitive load.
本文介绍了一种可带容性负载的高电压、高频响激励电源的设计方法及相应的实现电路。
The Short Circuit protection should be tested at other load rating.
短路保护测试是在其它额定负载时测试。
The cable ampacity in one circuit decreases with the load increase of another adjacent circuit.
负荷不均匀的双回路运行时，其中增加一回路负荷将使其临近回路的载流量减小。
The microwave switching matrix is to exchange messages between ATS and the circuit units under test, and to provide necessary load for these units.
微波开关矩阵主要是实现自动测试系统与被测电路单元之间的信息交换，以及为被测单元提供必要的负载。
The basic purpose of a shunt capacitor bank is to increase the local circuit voltage and or reprove the load power factor carried by the circuit.
并联电容器组的基本目的是要提高当地线路的电压，或提高引线路所带负荷的功率因数。
Overcurrent protective circuit, load driving unit, motor driving unit, electrical equipment, and power unit.
过电流保护电路，负载驱动装置，电机驱动装置，电气设备和电源装置。
Using LC tank circuit as the load of modified XOR, the frequency component desired can be extracted out.
改进的异或门中，利用LC谐振回路作为异或门的负载，提取出希望得到的频率分量。
Because the capacitor voltage always changes in the course of charging, and the equivalent load also changes in a large range, the load characters of charging circuit are required strictly.
由于电容在充电过程中，其电压不断改变，其等效负载也在较大的范围内变化，因而对充电电路的负载特性提出了较高要求。
A scheme of bidirectional thyristor phasing trigger composed by ICs is presented, and the trigger circuit fit for AC voltage regulator of inductive load is given.
提出了一种由集成电路组成的双向晶闸管移相触发器的设计方案，给出了适合于感性负载的交流调压电源的触发电路。
This paper introduces simulation methods of MCU hardware and software systems and help to solve actual problems by analyzing crystal circuit, electriferous reset and load capacity of the systems.
在单片机用户系统的设计中，必须对硬件和软件进行具体仿真。通过分析单片机系统的晶振电路、上电总清和负载能力来解决实际遇到的问题。
A simple and efficient model was presented for computing the effective capacitance of interconnect load based on simulation and integrated circuit process.
在大量仿真数据以及当前集成电路设计工艺的基础上，提出了一种简单互连线负载的有效电容计算模型。
According to the equivalent circuit model of non-linear load, a detecting approach of harmonic current in single-phase circuit based on fast iterative algorithm in active power filter is proposed.
根据非线性负载的等效电路模型，提出了一种基于快速跟踪算法的有源电力滤波器单相电路谐波电流检测方法。
Reliability, paths of lines, middle nodes, circuit number and type of lines, rebuilding and multiple load and running states were considered in the novel model.
该模型考虑了配电网优化规划中存在的可靠性、线路走径、中间节点、线路型号与回数、多负荷状念、多运行状态、原有电网的改建等多个方面。
The operation features of the load circuit of the electronic ballast are analyzed.
分析了电子镇流器负载电路在谐振点火阶段和稳态限流阶段的工作特性。
Double proportional, load sensitive hydraulic circuit.
液压油路采用双比例负载感应。
The energy performance of the BERL circuit is more excellent with larger load.
负载越重，BERL电路的低能耗优势越明显。
Based on highest current automatic current sharing technique, a load sharing control circuit was designed.
应用最大电流自主均流法，设计负载均流电路。
Interrupter circuit breaker has a strong ability to both cut off the load current, but also cut off the short-circuit current.
断路器具有很强的灭弧能力，既能切断负荷电流，也能切断短路电流。
Equipped with grounding switch load switch, can withstand short-circuit current.
配装接地开关的负荷开关，可以承受短路电流。
Its software is designed to calculate the running parameters of the AC drive system, including transformer, quadrant rectifier, DC circuit, inverter, AC motor and train load.
系统采用软件方式实时计算交流传动系统的运行参数，包括变压器、四象限整流器、直流中间回路、逆变器、电机及负载。
The protection functions of relay don't be affected by current intensity of circuit or load, impulse current, imbalance current and load characteristic.
监视器的保护功能不受线路或负载的电流大小，冲击电流、不平衡电流和负载性质的影响。
The load operation of a three-phase induction-voltage regulator is presented briefly. The related data, phasor drawing and parameters in secondary circuit, primary load circuit and imput are analyzed.
简要介绍了三相感应调压器的负载运行情况，对二次回路参数、负载时一次回路参数、输入参数、相关数据和相量图进行了分析。
The load operation of a three-phase induction-voltage regulator is presented briefly. The related data, phasor drawing and parameters in secondary circuit, primary load circuit and imput are analyzed.
简要介绍了三相感应调压器的负载运行情况，对二次回路参数、负载时一次回路参数、输入参数、相关数据和相量图进行了分析。
应用推荐