A new hierarchical approach for layout circuit extraction was presented to increase its efficiency.
为提高版图电路提取效率，提出了一种新的层次式版图电路提取方法。
VLSI layout circuit extraction provides a reliable tool for the estimation of circuit's performance.
集成电路版图提取为精确估计电路性能提供了可靠的手段。
The digital realization of monostable circuit and extraction of bit-synchronous signal with digital phase lock loop are also introduced in detail.
对于其中的单稳态电路的数字化和数字锁相环提取位同步信号也进行了详细的设计说明。
Interconnect geometric variation extraction is a key factor for the integrated circuit design for manufacturability research and development, under ultra deep sub-micro process nodes.
硅片上互连线几何变异提取对于超深亚微米工艺节点下集成电路可制造性设计研究开发极其关键。
Their specific results in the simple timing extraction circuit(STC) condition are compared with those from other deductive methods.
并在简单定时提取电路（STC）的具体情况下与其它推导方式的结论进行了分析比较。
In the paper, the calculating method of signal extraction filter pass-band according to the paper-counting speed and the utility circuit of separating strong interference in pass-band are given.
并针对点钞速度给出了信号提取滤波器通频带的计算方法，以及在带内分离强干扰的实用电路。
A general approach for node extraction of circuit layout and a node compaction method are given in this paper.
提出了一种版图电路节点提取及节点压缩算法。
The SPD R&D includes five modules: SPD bias voltage, pre-amplification, avalanche signal extraction, temperature control and digital control circuit.
将单光子探测器的研制分为偏置电压、前置放大、雪崩信号提取、温度控制和数字控制电路五个模块。
With a simulation experiment, the signal of tire burst is gained from the piezoelectric sensor. Then design a feature extraction circuit unit, also with the safety circuit.
由爆胎模拟实验得到了爆胎信号特征，由此提出了由爆胎特征提取电路、安全电路、逻辑判断电路、点火电路组成的控制器设计原理及压电供能的设计方法；
The equivalent circuit, structure, and parameter extraction of the model were described, and it was realized with the simulation tool of PSIM package.
描述模型的等效原理、构成和参数提取过程，并在PSIM软件包下建立其等效电路。
A new method for equivalent circuit parameter extraction of capacitor is proposed, and the characteristic of capacitor is discussed according to the extracted results.
提出了新的电容等效电路参数提取方法并对埋置电容进行了特性分析。
The design method of video signal's magnitude extraction circuit is expounded, and this design method is applied in the automatic dimmer system.
介绍了一个视频信号幅值提取电路的设计方案，并应用于摄像机自动调光系统。
Relative to other signa1's magnitude extraction circuit, this design method has such features:distinct design thought, simple circuit structure, low cost, high reliability and so on.
实验结果证明，相对其它幅值提取电路，该设计方案具有设计思路清晰、电路结构简单、成本低和可靠性高等特点。
On the precondition that the error is acceptable, we reduce the memory circuit before we do the logic parameter extraction so as to realize extraction automation.
参数提取前，在库参数精度受影响可忽略的前提下，对存储器先进行电路简化，使得存储器的提取自动化得以实现。
Printed Circuit Boards; Pyrolysis; Extraction and Separation; Synthesis; Modified Resin.
印刷线路板；热解；提取分离；合成；改性树脂。
Design flow of analog circuit begins with drawing schematic and includes simulation, layout, DRC/LVS check, parasitic extraction and post-simulation.
在完成版图设计后，还进行了几何规则检查和版图与电路一致性的 检查。
The Leach Solution is then processed in a 2 stage Copper Solvent Extraction circuit.
过滤液然后通过二级铜溶剂萃取流程进行处理。
The Leach Solution is then processed in a 2 stage Copper Solvent Extraction circuit.
过滤液然后通过二级铜溶剂萃取流程进行处理。
应用推荐