It is meaningful to take machining and cost during the calculation of torque, which provide a criterion in the design of hybrid stepping motor.
可见在转矩的计算中考虑加工和成本将给混合步进电机的设计提供一个有意义的判断依据。
The analysis of magnetic field in the gap is based on the calculation of torque ripple caused by various factors in-depth analysis and calculation.
本文在气隙磁场解析计算的基础上，对引起永磁电机转矩波动的各个因素进行了深入的分析和计算。
This method didn't need to integrate the torque control command of every flywheel and reduced calculation amount.
这种方法不需要对每个飞轮的力矩控制信号进行积分，减小了计算量。
This paper presents a torque control model for variable tension with automatic on-line calculation of winding diameter in winding drive inverter.
提出了一种卷绕传动中利用变频器实时完成卷径自动计算的变张力转矩控制模式。
Most of the fin stabilizers we use now are angle-feedback system, whose control torque is gotten by the calculation of fin Angle.
目前使用的绝大多数减摇鳍都是角度反馈系统，它通过鳍的转角来计算控制力矩。
Most of the fin stabilizers we use now are angle-control system, whose control torque is gotten by the calculation of fin Angle.
目前使用的绝大多数减摇鳍都是鳍角控制系统，它通过鳍的转角来计算控制力矩。
This paper introduced working principle of PM Claw-pole stepping motors, including magnetic circuits analysis and torque calculation method.
本文介绍永磁爪极步进电机的工作原理、磁路分析及转矩计算方法。
The method of torque capacity calculation and the principle of model selection for electro-magnetic clutch applied in hoist mechanism of tower crane are introduced in this article.
本文介绍了电磁离合器应用于塔式起重机起升机构的扭矩容量计算方法和型号选择原则。
It is analysised of some survey results of rotary kiln driving torque and revises the calculation formula now available.
对回转窑传动扭矩的实测结果进行了分析，对现有的计算公式进行了修正。
In this paper, formula of calculation of dynamic torque and loss of stretching force for coilers is established with two examples.
根据带钢卷取机的特点，用两种不同的方法，推导了计算卷取机动态力矩的公式，且用实例作了验证。
Discuss in detail the torque characteristics of hoister double-fed cascade adjusting speed system and the designing calculation of starting torque of hoister shearing resistor.
文中详细论述了提升机双馈串调系统的转矩特性和提升机切电阻时启动力矩设计计算。
An example of calculation shows that the result of calculation by graphic method conforms with that calculated by the torque factor method.
计算实例表明，这种方法和用扭矩因数法求得的结果基本一致。
Based on the complexity of analysis and calculation of magnetic behavior, an efficient method is put forward for the torque calculation of permanent magnetic gears.
基于磁性能分析计算的复杂性，提出了一种计算永磁齿轮传动力矩的有效方法。
The mathematical model on the calculation of recoiler dynamic torque(DT) and dynamic current(DC) are discussed. The calculation method on DT and DC by means of CAD is presented.
详细论述了卷取机动态力矩的数学模型及在控制系统中的实现问题，最后给出了采用CAD计算动态力矩和动态电流、确定相关工艺参数的方法。
Establishment of torque mathematic model for a variable speed turbo coupling is the key for analysis and calculation of system dynamic response.
建立调速型液力偶合器力矩特性数学模型是分析和计算机械系统动态响应的关键。
It also gives the calculation method for the torque of the worm and the power of the conveyor line.
并给出了蜗杆扭矩及输送线功率的计算方法。
The kinematics analysis makes the calculation of falling down torque easier, and is helpful for robot's control.
运动学方程的建立使倾翻力矩的计算变得方便，有利于机器人的控制。
Based on the consideration of nozzle ring pneumatic torque transmission, the torque of pneumatic force acting upon nozzle guide vane was acquired by calculation.
在考虑了喷嘴环气动转矩的传递过程后，通过换算，求出了气动力作用在喷嘴导流叶片转轴上的转矩。
The result of calculation shows that the relevant dimension and K entropy of torque and speed signals are different in varied operating condition.
计算结果显示，柴油机在不同工作状态时，其扭矩及转速信号的关联维数及K熵各不相同。
At last, finish the calculation of the corresponding joint torque according to the movements of the manipulator in order to guarantee the better position precision and expected speed and acceleration.
再根据机械手末端执行器的运动情况完成了相应关节力矩的计算，以使它们能以期望的加速度和速度运动，保证良好的位置精度。
Calculation formulations of corresponding dynamic torque measurement for different working states are presented.
章根据不同工况，提出了相应的扭矩动态测量计算方程。
The accurate calculation of cogging torque assists in optimizing the design of claw pole permanent magnet synchronous motors.
脉动转矩的准确计算是爪极永磁同步电动机优化设计的基本前提之一。
The calculation formula of the cogging torque are derived by the Fourier decomposition and the virtual displacement method.
利用傅里叶分解及能量虚位移法，推导了磁阻转矩的计算公式。
The calculation method which I used to solve electromagnetic torque need the magnetic field calculated only twice, thus reducing the amount of calculation, while the accuracy has improved.
该计算方法求解电磁转矩时只需进行两次磁场计算，从而减小了计算量，同时计算精度也有所提高。
Calculation formulation of corresponding dynamics torque measurement in different work state is presented.
根据不同的工作情况，提出了相应的动态测量扭矩的计算方程。
The second, the author deduces the torque calculation formula and calculates the output torque of the motor.
在第三章中利用磁路法法计算了本文设计的啮合式微型电机的输出参数。
The second, the author deduces the torque calculation formula and calculates the output torque of the motor.
在第三章中利用磁路法法计算了本文设计的啮合式微型电机的输出参数。
应用推荐