This method differs greatly from the present general calculation method in the stress distribution of controlled section.
此法与一般的计算方法相比在控制截面的应力分布方面有大的差别。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
The structure and load form of the absorbing tower is complex and regular design and calculation method cannot give its distribution condition of the stress and deformation.
脱硫吸收塔结构及荷载形式复杂，常规设计计算方法不能给出其应力和变形分布情况。
For a typical assembly stress problem, digital simulation is conducted by means of the hybrid method with different numerical calculation methods.
针对一个典型的装配应力问题，运用不同的数值计算方法，对混合求解法进行了数值模拟。
With the non-line finite element method, the numberical value calculation on the stress and deformation of surrounding rock of deep mine roadways has been presented.
采用非线性有限元法，对深井巷道围岩应力及变形状态进行了数值计算。
In the evaluation of the residual stress by the crack compliance method, different interpolation functions and their fit order had great effect on the calculation results.
在应用裂纹柔度法计算残余应力时，插值函数及其阶数的选择对计算结果的精确性有着较大的影响。
To cut down great calculation of assembling and disassembling of stiffness matrix in the nonlinear procedure, the initial stress method is introduced to resolve the nonlinear equations.
使用初应力法对非线性方程组进行迭代计算，避免了组装和分解总体刚度矩阵的繁杂而庞大的运算。
A calculation method is proposed to determine the crack tip stress intensity factors for sections on the basis of zonal generalized variational principles.
本文应用分区广义变分原理，提出了求解含有裂纹的型材应力强度因子的计算方法。
Verification calculation of transient temperature and stress distributions were performed with the finite difference method, and the results coincided with the measurements.
并用有限差分法对瞬态温度场与热应力进行了校核计算，其结果与实测完全吻合。
In this paper, we study theoretically infinitesimal element method for calculation of stress birefringence in polarization maintaining fibers.
本文研究了计算保偏光纤中应力双折射特性的微元算法，对其计算值进行了理论验证。
This paper describes the calculation method and process of stress amplitude and stress amplitude spectrum to evaluate the safety life time of steel structure for tower crane.
本文介绍了塔式起重机钢结构安全寿命评估中的应力幅及应力幅谱系数的计算方法和过程。
Then, the complex integral calculation problem in the reliability model of stress and strength interference was simplified by using the Monte Carlo Simulation Method.
其次，采用应力与强度干涉模型和蒙特卡罗模拟法，解决了可靠度计算公式中复杂积分的计算问题。
In the present paper, the rheologic characteristics of expanded graphite under this stress state is discussed and a method of quantitative calculation based on the theory of rheology is suggested.
本文以流变学理论为基础，讨论了柔性石墨材料在此种应力状态下的流变特性，并给出了定量的计算方法。
This article presents an analysis of the contact stress of rolls in two-cross-roll straightener and gives a method for the calculation.
在实践的基础上对二辊矫直机辊面接触应力的计算进行了理论分析，给出了辊面接触应力的计算方法。
According to the principle of effective stress, this paper puts forward the theoretical basis for determining foundation's bearing capacity, presents the rational calculation method.
根据有效应力原理，提出了确定地基承载力的理论依据，给出了合理的计算方法。
In this paper a right formula of laterad stress was derived by the direct method, and at same time a formula of the vertical strain for calculation was also derived.
本文用直接法导出侧向应力的正确公式，同时还导出了竖向应变的计算公式。
Combining practical matters, a method of the stress calculation of circular ring plates under press loading using flat circular plates formula was introduced.
本文结合实际问题，给出了利用《应力应变公式》中的等厚平圆板公式对受压环板应力的理论计算方法。
Through the calculation of the finite element method(FEM) models for double circular arc profile spiral bevel gear, the stress changing pattern along the length of the tooth is obtained.
用有限元方法，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算。通过应力计算结果的分析，得出了凸、凹两齿侧应力沿齿长的分布规律。
Design calculation of dual semi-ring (DSR) high pressure vessel is introduced in this paper. It USES the method of stress analysis based on the theory of shells.
介绍了双合环高压容器的设计计算，它应用基于壳体理论的应力分析方法。
The paper has established the calculation method of the equivalent modulus of elasticity of foundation that is based on the principles of thermal stress equivalence.
利用有限元法对温度应力进行了大量计算，在此基础上建立了以温度应力等效为原则的基顶当量回弹模量换算方法。
The paper studies the simplification calculation method of concrete shrinkage and the calculation of temperature and shrinkage stress that takes the effects of concrete creep into account.
讨论了混凝土收缩简化计算方法及混凝土徐变对温度及收缩应力计算的影响；
By the use of finite element method, the stress calculation of damageable zone was conducted by the author, and proved that the strength of that zone had no problem.
作者采用有限元法对易损部位进行了应力计算，证明该部位的强度没有问题。
The discussion has been laid stress on the calculation method of balancing moment on each joint axle which affects directly on dimensions and weights of the structure.
着重讨论了直接影响结构尺寸和重量的各关节轴上平衡力短的计算方法。
Finite element method is used to study stress and place moving field inside the structure and electric measure method is utilized to verify the result of calculation.
利用有限元方法对该结构内部的应力场和位移场进行了研究。
According to the space regularities of distribution of ground loss and by image method theory, the calculation formulas of superimposed stress are deduced.
根据土体损失的空间分布规律，应用镜像法原理，推导了土体损失产生的附加应力计算公式。
This article researches on the calculation method of thermal stress of cement concrete pavement on lean concrete base course.
本文围绕贫混凝土透水基层水泥混凝土路面温度应力计算方法展开研究。
The thermal residual stress was calculated by the finite element method. Both testing and calculation data proved the reliability of testing data.
采用有限单元法计算了反射镜坯体的热残余应力，通过对比验证了测试结果可靠性。
By utilizing theory of elastic mechanics, this paper conducts circular compensator stress analysis. Research gives a calculation method of best pre-stress value.
本文利用弹性力学理论，对圆形补偿器进行应力分析，研究预加应力最佳值的计算方法。
The calculation of the initial stress (or initial strain) singular integrals in elastoplastic boundary element method is a difficult, but an important problem.
弹塑性边界元法中初应力(或初应变)奇异体积分的计算一直是一个较为困难、但又是非常重要的问题。
The calculation of the initial stress (or initial strain) singular integrals in elastoplastic boundary element method is a difficult, but an important problem.
弹塑性边界元法中初应力(或初应变)奇异体积分的计算一直是一个较为困难、但又是非常重要的问题。
应用推荐