The calculated load-settlement curve and that obtained from in-situ test are in good agreement, which verifies the model.
计算的荷载-沉降曲线与现场试验测得的曲线吻合良好，验证了该模型的适用性。
Formulas marked as "Compute on page Load" are calculated only once when the page is first sent.
被标记为“Compute onPageLoad”的公式仅在首次发送页面才进行计算。
The safety length to connect apparatus component and load cable was calculated and given.
文中还计算出与电器元件连接负载电缆的安全长度。
The relationship between velocity and extern load for the two cooperative behaviors are calculated based on the energy conservation.
并且分别计算了这两种协作行为得出的肌肉所负荷外力与收缩速度的关系。
With the welding spot fatigue lifetime pre-estimation method, by combination of the finite element analysis and stress calculation, the welding spot fatigue damage under actual load can be calculated.
采用焊点疲劳寿命预估方法，通过有限元分析并结合应力计算，即可计算出实际载荷工况下的焊点疲劳损伤。
The profiles are calculated in such a way that, under normal load conditions, life-reducing edge stresses do not occur at a tilting angle of up to 4' between inner ring and outer ring (Table 5.2).
通过这种方式计算的轮廓，在正常的载荷情况下，内外圈之间的偏斜角度超过4＇时不会发生缩减寿命的边缘应力（表5.2）。
In this method, based on the measured strain values, the joint load is calculated by the fitted curve equation and compared with the total load applied during test.
该方法以测量的应变值为基础，由拟合的曲线方程计算接头载荷，并与试验时施加的总载荷对比。
On this basis, back electromotive force without load and with load is researched, simulated and analyzed, and cogging torque is analyzed and calculated in different dimensions of magnetic steel.
在此基础上，仿真了空载和负载下的电机反电动势，并且对不同磁钢尺寸下的定位力矩进行了分析计算。
And then the power of servo motor is calculated according to crank press working load, kinematical characteristic, torque and rotational momentum.
以变速驱动压力机的工作负荷、运动特点、工作总功、力矩和角动量为基础，计算其驱动电动机所需的功率。
If the actual load is a combined radial and axial load, then an equivalent static bearing load must be calculated.
如实际负荷为径向和轴向复合负荷，则必须计算当量轴承静负荷。
The minimum fitting pressure and tightness using to transfer load can be easily calculated. It provides an efficiency tool for tight fitting's design and calculating.
该系统可完成有关过盈配合的最小配合面压强、传递载荷所需的最小过盈量等参数的计算，为过盈配合的设计与计算提供了一个高效的工具。
The compression of the pile in the pile group can be determined by static load test. The settlement of the pile toe is calculated by layer wise summation method.
群桩中桩身压缩由单桩静载试验得到的桩顶沉降与桩端沉降之差求得，群桩的桩端沉降由分层总和法计算。
The internal force produced in live load is calculated by manual loading method.
活载产生的内力采用手工加载的方法计算。
The stress and deformation of crankshaft are calculated by finite element method with six load boundary conditions and three displacement boundary conditions.
分别采用六种载荷边界条件和三种位移边界条件对曲轴应力和变形进行了有限元分析；
The load current is calculated from the supply voltage and the load power.
负载电流的计算应该根据工作电压和负载的功率计算。
The effect of random wind load applied on the structure is simulated and calculated. And random wind vibration response of the structure is studied deeply.
模拟计算了施加于结构的随机风荷，并对结构的随机风振响应作了较深入的研究。
The fluid load in pipeline is calculated, that is calculating the pressure distribution of pipeline.
计算管线内部流体荷载，也就是管系的压力分布计算。
At the same time, leakage magnetic coefficient of commutating pole is calculated and analyzed by magnetic flux in itself and gap at rated load.
同时，利用额定负载时换向极身中的磁通与穿过气隙的总磁通，对换向极漏磁系数进行了计算与分析。
The time history of water hammer in pipeline in the condition of unit emergency load dump is calculated by characteristic line method.
在水电站机组丢弃负荷情况下，利用特征线法计算管道内的水击荷载时间历程。
Based on the magnitude of active soil pressure, parameters like bend are calculated applying evenly distributed load method.
本文根据主动土压力大小，应用均布荷载梁计算方法，计算其挠度等参数。
As a rule, power and load measurements shall be performed at the prototype, after which they shall be compared to the calculated values.
一般来说，应在样机上进行功率和负荷测量，然后与计算值进行比较。
The internal forces caused by the action of racking load, which is calculated, are the same as the results of the actual measurement.
根据工程实际计算了变形荷载作用下的内力，其结果与工程事故的情形一致。
Finally, buckling load and mode can be calculated from the characteristic equation.
最后由屈曲方程计算含内埋矩形脱层壳的屈曲载荷和屈曲模态。
In the end, the wind characteristics of system were analyzed and wind load of several kinds of cable-truss Supporting system were calculated using wind load norm of the glass curtain.
最后，对体系的风振特性进行了分析，用幕墙风荷载规范对几种索桁支承体系形式进行风荷载计算。
The stress concentration analysis was done by the finite element method and boundary element method. The fatigue strength and the strength under the static load were calculated.
对螺纹槽管进行了疲劳强度计算，并采用边界元和有限元法对螺纹槽管的应力集中进行了数值分析及静载强度计算。
Its dynamic characteristics involved with speed and altitude, the influence of the inclined Angle of the trajectory plane and load on it are also calculated and analyzed in this paper.
推导了斜筋斗计算公式，并计算分析了其速度、高度特性，及轨迹平面倾斜角、过载对斜筋斗的影响，计算结果与理论分析一致。
The loading process is designed on the basis of the cracking and yielding loads and earthquake action as calculated for seismic load of fortification intensity.
根据计算的各抗震设防烈度对应的地震作用及开裂荷载、屈服荷载设计出加载制度； 采用液压伺服装置进行低周反复荷载试验。
The loading process is designed on the basis of the cracking and yielding loads and earthquake action as calculated for seismic load of fortification intensity.
根据计算的各抗震设防烈度对应的地震作用及开裂荷载、屈服荷载设计出加载制度； 采用液压伺服装置进行低周反复荷载试验。
应用推荐