Level3: Tolerance matching of freewheel bushings. Factory only.
级别3：飞轮轴套的公差矫正。只有工厂可以操作。
Upper and lower bushings are standard for smooth valve operation.
上部和下部衬套符合流畅平稳轻松操作阀门的标准要求。
Bronze Bushings: High side load capabilities, self lubricating, long life.
青铜衬套：高侧的负载能力，自润滑，寿命长。
Exposed to elevated temperatures with some finishes intact or bushings installed.
暴露到恶劣的温度条件下，接触到涂层或装有衬套。
Note that on Fire Protection models adaptor bushings may differ from illustration.
注意：消防防火型号阀门的适配器衬 套可能与图示不同。
The bushings included with many starter cars eventually become sloppy and wear out.
该衬套包括许多起动汽车最终成为马虎和磨损。
Many RC cars include bronze bushings on their moving parts rather than ball bearings.
许多遥控汽车包括他们的移动部件，而不是球轴承青铜衬套。
Step bushings are placed in all key pivot areas to increase strength and reduce stress.
重要枢 轴均采用阶梯衬套，以便增加强度和减小应力。
Un-housed VCA shipped as Coil Assembly and Field Assembly, without shaft and alignment bushings.
非封装音圈调节器线圈，现场组装，船运不配自调整轴承和绝缘套管。
This should last at least until I locate or learn to machine bronze bushings or maybe I'll leave it.
这应该至少持续，直到我找到或学习机青铜衬套或也许我会离开。
Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support.
衬套：在三个位置上配置轴支撑，有利于轴校直和执行机构的支撑。
The molten glass flows through orifices and temperature resistant bushings at the base of each furnace.
熔融的玻璃液流过喷丝头以及熔炉底部的耐高温衬套。
The linear bushings and linear sets of the eLINE series are supplied in a clearance-free configuration.
线性衬套和埃利纳系列线性集提供了无间隙的配置。
It is a specialized manufacturer that produces wearing parts like fixed bushings and removable bushings.
系生产轴承附件——紧定衬套、退卸衬套系列产品的专业厂家。
Guide rods are supported by specially designed guide bushings providing optimum support of dynamic loads.
导杆的支持，特别设计的指导，提供最佳的动态负载支持轴套。
Recommended for use on aluminum conduit, bolts, bushings, fittings, flanges, nuts, pipes, plugs and screws.
推荐使用在铝管、螺栓、套管、配件、法兰盘、螺母、管线、塞子和螺丝。
Other applications where high carbon steels are well suited include drill bushings, locators, and wear pads.
高碳钢也很适用的其它地方包括钻头夹头、定位仪和耐磨垫。
Bushings (4) : Furnishes shaft support at three locations for positive shaft alignment and actuator support.
衬套(4)：在三个位置上配置轴支撑，有利于轴校直和执行机构的支撑。
Do not drop or kick the master rotary bushings into position. Always use insert tools and hoist them into place.
不要投放或踢放大方瓦，应当用专用工具提着放入。
A special fixture-cylindrical sleeve is presented for mechanical processing of bushings with small inner diameter.
针对小孔径瓷套机械加工难度大的问题，介绍了一种特殊的工艺装备套筒。
This instrument is appropriate for testing cables, capacitors, transformers, bushings, coils of high voltage machines, etc.
仪器适用于测试电缆、电容器、互感器、套管和高压电机的线圈等。
A higher gear after heat treatment the hardness and strength, and the shaft can be replaced with bushings installed in the operation.
齿轮经热处理有较高的硬度和强度，与轴一同安装在可更换的轴套内运转。
By turning a pair of composite eccentric bushings in the chassis and top deck, you can move the complete assembly forward or backward.
把一对复合偏心轴套在底盘和顶部甲板上，您可以提出完整的大会，向前或向后。
The solution was a plastic, external cover (including the switch handle) isolated from the mechanism housings by large rubber bushings.
解答是塑料，外在盖子(包括开关把柄)与机制住房被隔绝由大橡胶轴衬。
Our company's main automotive water, air tube, dust cover, silicone tube seal, pull, engine brackets, bushings and other rubber products.
本公司主营汽车水管、空气管、防尘套、硅胶管、密封条、拉线、发动机支架、衬套等橡胶制品。
SIBA Capacitor protection fuses can easily be fitted direct onto capacitor bushings, because they are fitted with threaded holes at both ends.
待职电容器保护保险丝可以轻松地装上直接上电容器衬套，因为他们是装有螺纹孔两边。
While pulling the BHA through the rotary table, the Driller must stop when stabilisers reach the table and have the Floormen remove the bushings.
当起钻到BHA，扶正器到达钻盘面时，司钻必须刹住刹把，让钻工移开方补心。
They include a wider track front and rear, suspension knuckles that lower the roll center, larger anti-roll bars, and revised bushings and shocks.
这些措施包括更广泛的轨道前方和后方，暂停关节，降低轧辊中心，大型防倾杆，并修订衬套和冲击。
According to the usage, the insulators can generally be divided into three broad categories: line insulator, substation post insulator and bushings.
按用途一般可分为线路绝缘子、变电站支持绝缘子子和套管三大类。
The die forging process for the small type bearing bushings has been described in this article, as well as the design outline of the assembled sleeve die.
介绍了小型轴承套的胎模锻造工艺，并详述了组合套模的设计要点。
应用推荐