In this paper, the transient modeling with distributed parameters of bus, bushing in GIS are presented.
提出了GIS母线、管线分布参数的暂态电路模型。
The designer may lower the pressure on the packing by placing a throat bushing in the pump case (Figure).
设计者可在泵壳内放置喉道补心以降低在填料上的压力(图)。
In some cases the small end of the rod is clamped to the pin or has a bushing in it to allow the pin and rod oscillation.
在一些情况下,连杆小端夹定在活塞销上或在连杆里有一套管,这样可以使得活塞销与连杆能够共同摆动。
The type selection of high voltage bushing in UHV transformer below air-cooling island and its operation and maintenance are discussed.
对运行在空冷岛下方的超高压变压器高压套管的选型及运行维护等进行了探讨。
It's a 4.5-link system that includes a unique, L-shaped upper control arm that attaches to the knuckle at one end and incorporates a ride bushing in the rear.
这是一个4.5链接系统,包括一个独特的,L形上控制手臂关节的重视,一端采用了乘坐在后面套管。
It is primarily fixed in the bushing in the pump (pump tank) and placed in the pump cylinder screw, and with the active engagement of the two driven screw formed.
它主要是由固定在泵体中的衬套(泵缸)以及安插在泵缸中的主动螺杆和与其啮合的两根从动螺杆所组成。
The elastic coupling characteristics of the unsymmetrical rubber bushing in the axial and symmetrical radial directions, affect the handling stability of the vehicle.
非对称式橡胶衬套在轴向和对称径向存在弹性耦合特性,对汽车的操纵稳定性有一定的影响。
Applying voltage into the bushing tap method for preventive test of converter transformer value side bushing in HVDC, especially in the future for UHV, will have better practical value.
末端加压法对高压直流输电系统所用换流变压器阀侧套管预防性试验,特别是将来特高压直流换流变压器阀侧套管预防性试验具有较高的实用价值。
In this, can use repair drive shaft and bushing method to recover its normal fit clearance.
遇此,可采用修主动轴或衬套的方法恢复其正常的配合间隙。
Based on worksite practice, the paper introduces Cleaning and Overhaul Technology of the chock, bushing, sleeve which are the key parts in the oil film bearing.
本文以现场实际经验为基础,重点介绍了轴承座、锥套和衬套这三个油膜轴承中关键件的清洗和检修技术。
In this experiment, the flame stability under large bushing is better than under small bushing.
在实验中,大套管实验工况的火焰稳定性比小套管要好。
The device as set forth in claim 9, wherein the bushing is configured to substantially prevent rotation and drift of the shear pin interfaces.
该装置所规定的索赔9,其中套管配置为防止大量轮换和漂移的剪切针接口。
The device as set forth in claim 9, further comprising a shear pin interface mounted in the at least one bushing, wherein the shear pin interface is configured to receive one of the shear pins.
该装置所规定的索赔9,进一步组成的剪切引脚接口安装在至少一个套管,其中剪切引脚接口配置为收到剪切销。
There was no damage found inside, but there was a little of metal powder in the arc chamber and porcelain bushing and some of the powder has been burned.
阐述了返厂解体检查的情况,内部未发现损伤,但灭弧室和瓷套内有微量金属粉末,部分有灼痕。
Bushing is one of the most important insulation parts in transformer.
套管是变压器中一种重要的部件。
In some instances the reinforcement can be achieved using small aluminum tube as bushing.
在一些例中钢筋能被达成以小的铝管作为桥衬。
In addition, the calculation method of aperture shrinkage is derived, and the real machining tolerance zone of bushing aperture is determined.
另外推导了孔径收缩量的计算方法,确定了衬套孔径的实际加工尺寸公差。
Oilpaper capacity type wall bushing is used for insulation and fixed HV or EHV conductor that crosses the wallboard of building in power plant and substation mainly.
油纸电容式穿墙套管主要用于发电厂、变电站中引导高压或超高压导线穿过建筑物的墙板,作为导电载流和高压对地墙板的绝缘及机械固定用。
Based on worksite practice, the paper introduces Cleaning and Overhaul Technology of the chock, bushing, sleeve which are the key parts in the oil film bearing.
本文针对薄壁衬套类零件易产生加工装配变形的问题 ,根据实际经验提出了解决措施 ,经实践使用证明 ,效果理想。
Connection of lead and bushing shall be tight and correct, bushing should be in good condition.
引出线与套管的连接应牢靠,接线正确。套管应完好无损。
Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.
连接条和接线柱的焊接必须使极柱顶部和盖子的铅衬套与连接条环口或接线柱完全熔焊牢固。
This paper presents the oil impregnated paper condenser bushing with short lower for power transformer used in UNENTA system, Egypt, with its electrical parameters design calculation and test results.
介绍了用于埃及unenta公司电力变压器的短尾油纸电容式变压器套管的电气性能、设计计算及试验结果。
This paper introduces the feature of white spots in cylinder bushing and reveals the cause by simulation.
针对离心铸造汽缸套的白斑特征,以模拟试验手段探寻原因。
A kind of heating technology of directly heating crude oil in the oil tube by the oil tube and bushing is developed.
提出了一种利用油管和套管作为发热体直接加热油管内原油的方法。
Pilot bearing in crankshaft. The pilot bearing in the crankshaft is usually either a Bushing or a Ball bearing.
曲轴上的导向轴承:曲轴上的导向轴承一般或者是轴瓦,或者是球轴承。
This article has described the manufacturing process of the compound bushing rolls in the aspect of melting, pouring, forging, heat treatment and machining.
从冶炼、浇注、锻造、热处理、机械加工等方面对复合镶套轧辊的制造过程进行了介绍。
The conductive loop partial overheat fault caused by improper design and installation of the through lead wire in transformer bushing is analyzed. The preventive measures are presented.
分析了因变压器套管穿芯引线设计及安装不合理导致的导电回路局部过热性故障,提出了防范措施。
Bored secant pile is mostly constructed by bushing pile rig in our country.
咬合桩在国内一般使用套管钻机施工。
In order to achieve the necessary inclination angleand prevent tipping, transformer insulating sheath the upper porcelain bushing withrope tied in a rope.
为了达到必要的倾斜角度并防止翻倒,变压器绝缘护套上部瓷套需用绳绑在吊绳上。
In order to achieve the necessary inclination angleand prevent tipping, transformer insulating sheath the upper porcelain bushing withrope tied in a rope.
为了达到必要的倾斜角度并防止翻倒,变压器绝缘护套上部瓷套需用绳绑在吊绳上。
应用推荐