Blind-hole lower bushing prevents leakage.
“盲孔”下部衬垫能够防止泄漏。
Master cylinder bushing at the clutch pedal.
离合器踏板处的总泵衬套。
You'd better embed a wall bushing at the corner.
最好在转角处预埋一个穿墙导管。
The transformer shall employ pure porcelain bushing.
变压器采用纯瓷套管。
Oil filled bushing should have plugs for test of power factor.
充油套管应带有用于进行功率因数试验的接插头。
The cast iron rod bushing provides maximum load bearing support.
铸铁连杆衬套提供最大承重的支持。
All bus and the ramus bus are covered with pyrocondensation bushing.
所有母线和分支母线都用热缩套管覆盖。
Stem: Stem has long engagement with yoke bushing for accurate seating.
阀杆：阀杆与轭架有很长的啮合段，有助于阀座密封的精确对准。
The function of a bushing is to prevent metals from touching one another.
衬套的作用是阻止金属的彼此碰撞。
Bored secant pile is mostly constructed by bushing pile rig in our country.
咬合桩在国内一般使用套管钻机施工。
Valve core and valve seat or bushing deactivation, valve lever curving and so on.
阀芯与阀座或衬套卡死，阀杆弯曲等。
File off both bores to the hexagon of the insertion bushing using a needle-point file.
用细锉将两个孔锉成镶入衬套的六边形。
Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.
上紧叶片弹簧加压机直到衬套凸缘的底部扎实地扺住叶片弹簧的孔眼。
Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.
齿轮泵主动轴与衬套磨损后，其配合间隙增大，必将影响泵油量。
In this experiment, the flame stability under large bushing is better than under small bushing.
在实验中，大套管实验工况的火焰稳定性比小套管要好。
Connection of lead and bushing shall be tight and correct, bushing should be in good condition.
引出线与套管的连接应牢靠，接线正确。套管应完好无损。
It is not considered meaningful to try to estimate or calculate the service life of an FW bushing.
估计或计算FW轴套的使用寿命被认为是缺乏意义的。
The bushing ring flange suitable temperature is decided by the designer according to the situation.
衬环法兰的适用温度由设计者根据情况决定。
Acting as an important accessories of transformer, the bushing should have a lower dielectric loss.
套管作为变压器的配套件，其介损应当较低。
Taper ceramic bushing for spindle is developed for machining center, so that the performance is improved.
针对加工中心研制了主轴锥孔陶瓷衬套，使机床的性能得到改善。
The designer may lower the pressure on the packing by placing a throat bushing in the pump case (Figure).
设计者可在泵壳内放置喉道补心以降低在填料上的压力(图)。
This paper introduces the feature of white spots in cylinder bushing and reveals the cause by simulation.
针对离心铸造汽缸套的白斑特征，以模拟试验手段探寻原因。
The new full-enclosed explosion-resistant oil-paper capacitor bushing and its characteristics are introduced.
介绍了一种新型全密封阻爆式油纸电容套管及其性能和特点。
The correctness of this algorithm is verified by the processing results of on-site data of transformer bushing.
对变压器套管现场数据的处理结果验证了该算法的正确性。
Through development and on-board test of ZA alloy bushing, its wearing performance has been further demonstrated.
通过ZA系列锌铝合金轴套的研制和装机试验，进一步证明其耐磨性能。
The kelly bushing (KB) has an inside diameter profile that matches that of the kelly, usually square or hexagonal.
方钻杆补心的内径通常与方钻杆的外径（通常是四方钻杆或六方钻杆）相匹配。
Depth measurements are commonly referenced to the KB, such as 8327 ft KB, meaning 8327 feet below the kelly bushing.
井深测量通常是指方钻杆补心高度，如补心高度8327英尺，就意味着在方钻杆补心以下有8327英尺的深度。
A kind of heating technology of directly heating crude oil in the oil tube by the oil tube and bushing is developed.
提出了一种利用油管和套管作为发热体直接加热油管内原油的方法。
Notably no varus collapse due to bushing failure was noted despite a high percentage of high-energy unstable injuries.
值得注意的是没有发现一例因套管失效而导致的内翻塌陷，尽管高能量不稳定性损伤占有很高比例。
Notably no varus collapse due to bushing failure was noted despite a high percentage of high-energy unstable injuries.
值得注意的是没有发现一例因套管失效而导致的内翻塌陷，尽管高能量不稳定性损伤占有很高比例。
应用推荐