Introduces how to connect the DSP to PCI Bus in brief and choose the means of using special PCI Bus interface chip to achieve it.
介绍DSP芯片如何桥接到PCI总线，并选择利用专用接口芯片的方法来实现。
The selection principle of bus interface chip and solution of bus conflict are introduced, together with its concrete hardware circuits and software block chart are given.
分析了总线接口芯片选择原则和总线冲突解决方案，给出了系统实现的硬件接口电路和软件实现详细框图。
Based on the USB bus interface chip CH375, we design the locomotive signals data recording system, and detail the design of communication interface of CH375 and TMS320F2812.
基于USB总线接口芯片CH375，设计了机车信号记录仪数据记录系统，并详细阐述了CH375与TMS320F 2812之间的接口设计。
SPC3 is a intelligence interface chip which is used in the open field bus PROFIBUS-DP.
SPC 3是一种用于PROFIBUS - DP开放式工业现场总线智能化接口芯片。
In this article, to carry the 6-axis motion controller out, a method of using PCI special interface chip PCI9052 to be a interface bridge of PCI bus and DSP (TMS320LF2407), was introduced.
文章介绍了一种采用PCI专用接口芯片pci9052作为PCI总线与DSP (TMS320 LF 2407)的接口桥接器，实现6轴运动控制卡的硬件设计方法。
The other module is PCI bus interface circuit. PI7C8150B chip of PERICOM Corporation is used to finish transmission of the image data.
另一个是PCI总线接口电路，本设计中采用PERICOM公司的PCI桥接芯片PI7C8150B实现图像数据的传输。
CAN-BUS interface adopts protocol control chip SJA1000 plus receiving and sending chip 82c250. Ethernet interface adopts Ethernet controller RTL8019AS as physical transmission media.
CAN总线接口采用协议控制芯片SJA1000，配以收发器82c250。以太网接口采用以太网控制器rtl 8019as作为物理层传输媒介。
The VHDL program embedded in the FPGA chip includes: interface combine ISA bus and FPGA, serial asynchronous communication module for transmitting and receiving.
该接口卡FPGA芯片内部VHDL程序含：ISA总线与FPGA接口、串行异步通信发送及接收模块。
Thus, the interface design of multi-DSP and CPCI bus with FPGA and bridge chip PCI9656 is described in detail.
本文详细介绍如何通过FPGA和桥接芯片pci9656实现多dsp与CPCI总线的接口设计。
The method which integrates PCI bus interface and control logic into a FPGA chip improves the integration density and transplantation of system.
该方法将PCI总线接口和控制逻辑集成于一片FPGA中，提高了系统的集成度和可移植性。
We study and analyze PCI bus protocol and apply PCI9050's interface chip to design the interface card of PCI bus and compile drive software of its interface card.
对PCI总线协议进行了分析和研究，采用PCI9050接口芯片设计了PCI总线接口卡，编写了接口卡的驱动程序。
The design includes designs of different can controllers for different data nodes, the can module controlled by single chip computer and can bus interface based on DSP TMS320LF2407A, etc.
其设计包括不同数据节点的CAN控制器，及单片机控制的CAN接口模块和基于DSPTMS320 LF 2407a的CAN总线接口等。
The design includes designs of different can controllers for different data nodes, the can module controlled by single chip computer and can bus interface based on DSP TMS320LF2407A, etc.
其设计包括不同数据节点的CAN控制器，及单片机控制的CAN接口模块和基于DSPTMS320 LF 2407a的CAN总线接口等。
应用推荐