The way of building finite element modeling and the geometrical similarity of model are also discussed in the paper.
文中还讨论了有限元建模的方式与建模的几何相似性。
Then two principal improving aspects of building finite element model and the foreground of the research are discussed.
最后提出有限元建模的两个主要改进方面及其研究趋势。
The influence of the technology about building finite element model for the automobile dynamic analysis are studied in this article, and build the car body adapt to dynamic analysis.
本文研究了有限元建模技术对车身动态分析的影响，建立起适合动态分析的车身有限元模型，在此基础上，进行了结构和声场的谐响应分析。
With the finite element method, the quantity of a building of air-leaking has been analysed in nature conditions.
在实测的基础上，建立了门窗渗漏模型，借助有限单元法，对整幢建筑物在外界环境下的渗漏量进行了定量分析。
The pulsating method is used to test the dome structure of the building under pulsation wind. Measured experimental data are compared with those obtained from the finite element analysis.
在脉动风的作用下，对穹顶结构进行脉动法实测，将实测值与有限元分析结果进行比较。
Because the software of ANSYS has the characteristics such as model building simply, fast and conveniently, it becomes the representation of large universal finite element procedure.
ANSYS软件具有建模简单、快速、方便的特点，因而成为大型通用有限元程序的代表。
Because the software of ANSYS has the characteristics such as model building simply, fast and conveniently, it becomes the representative of large universal finite element procedure.
ANSYS软件具有建模简单、快速、方便的特点，因而成为大型通用有限元程序的代表。
The method was discussed for how to integrate optimizing and building model with finite element analysis on 3D development and analysis of outer-tooth gear pump through UG design platform.
探讨通过UG设计平台，如何将优化程序、3D模型建立、有限元分析等，有机集成于外啮合齿轮泵齿轮3D设计和分析中去。
The finite element modal analysis of an effective model has been done after building up its analytic model by applying modern CAD techniques.
利用现代CAD技术建立有效的有限元分析模型，并在此基础上对其进行有限元模态分析。
A method of building the finite element model of swing movable teeth reducer was put forward according to the characteristics of the construction of swing movable teeth reducer.
针对摆动活齿减速器的结构特点，提出了摆动活齿减速器的有限元模型的建模方法。
Based on the tunnel excavation engineering practice, finite element method is selected to analyze the influence of building pile foundation induced by adjacent tunnel excavation with different depths.
基于隧道开挖的工程实例，采用有限元方法，分析了临近桩基的隧道开挖对建筑物桩基的影响。
For controlling the cracks in concrete small hollow block building(CSHBB) wall, a nonlinear finite element method was proposed.
为了控制混凝土小型空心砌块建筑（CSHBB）中的墙体裂缝，提出了一种非线性有限元分析方法。
Adopting elastic finite element analysis method to analyze temperature stress in large area concrete beam-slab structure may provide basis for extra huge building design.
对此采用一套以弹性有限元分析为基础的方法，对大面积混凝土梁板结构温度应力进行分析，可为超大建筑物的设计提供依据。
The finite element analysis techniques and building model approach, including the mesh convergence study and the selection of deformation parameters etc.
探讨了管道三通塑性失效有限元分析中的建模技术，包括变形参量选取，网格收敛性研究等。
Base on of the basic theory of stability analyses, Finite element model building and the elements selection are analysed.
基于拱桥稳定性分析的基础理论，给出拱桥有限元建模的单元选取及建模方法。
The methods of analyzing the strength of complex mechanical structure were studied through the application of the finite element method, and the methods of building model and gridding were discussed.
研究了用有限元法对复杂机械结构进行强度分析的方法和步骤，对复杂机械结构的建模方法和网格划分进行了探讨。
Building a finite element model of bridge, which accurately reflects the true structure's stiffness and mass distribution, can improve the precise of dynamic analysis results of structure very much.
有限元模型对桥梁质量和刚度分布模拟是否准确，直接影响桥梁的动力分析结果。
In design of building structures the bottom plate on elastic foundation is calculated in common using finite element method or calculation charts.
在建筑结构设计中弹性支承板的计算一般采用有限元法和图表法。
Building nonlinear finite element models using ANSYS program, And in the light of previous experimental to verify the correctness in the article.
本文利用ANSYS程序建立了非线性的有限元模型，并参照前人试验验证模型分析程序的正确性。
Incorporating with the model dynamic experiment and Finite-Element seismic analysis of a shear-wall superhigh building, paper gives the earthquake resistant behavior of such structures.
本文结合一超高层钢筋混凝土剪力墙一核心筒结构的模型试验与有限元动力分析，对超高层筒体结构的动力特性作了具体研究分析。
On the base of finite element method about contact problem, building models of the flanged connection and the sleeve connection of aircraft is introduced.
在接触问题有限元法的基础上，介绍飞行器的盘式连接、径向螺钉套接接触模型的建立。
The method of the spherical gear parameter model building and its finite element analysis under the ANSYS circumstance is studied thoroughly.
研究基于ANSYS的球齿轮参数化模型生成技术及其有限元分析技术。
In this paper, the finite element method is used for overall stability analysis of tall building tubular structures.
本文将有限元法用于高层筒体结构的整体稳定分析。
During building the finite element model of three-dimensional car parking lot rigid-framed structure, discusses it's generating method and the relative part which should be worth attention.
在构建立体停车库刚架结构体的有限元模型时，论述了其生成方法和其中应注意的环节。
The method of Virtual Prototype Building and Finite Element Analysis is theoretically meaning and practically valuable for design and performance simulation of complex mechanical system.
其中的虚拟样机建造方法与有限元分析手段在共同建立的联调平台下解决复杂机械系统设计及性能仿真方面具有理论意义与实用价值。
The response surface approach and the finite element method are introduced to the earthquake-resistant reliability analysis of unequal height mill building, and a general method is presented.
把响应表面法和有限元法引入不等高厂房抗震可靠性分析中，提出了一般方法。
Taking the Second Long Distance Telecommunication Hub Project of Zhengzhou for an example, this paper makes models of solid finite element to super-length building.
以郑州第二长途电信枢纽工程为例，对超长建筑结构进行整体有限元建模。
This thesis find the basis paths and methods of automobile panel simulation and finite element model building by researches of taillight supporter and other auto panels;
本文通过对汽车尾灯支架及其它一些覆盖件的研究找出了覆盖件有限元模型建立及模拟的基本流程和方法；
This thesis find the basis paths and methods of automobile panel simulation and finite element model building by researches of taillight supporter and other auto panels;
本文通过对汽车尾灯支架及其它一些覆盖件的研究找出了覆盖件有限元模型建立及模拟的基本流程和方法；
应用推荐