By changing the brush diameter, density, the gap between brush bristles and the axis, and the shape of brush edge, the influence of the structure parameters on the seal performance is obtained.
通过改变刷毛直径、刷毛密度、刷毛与轴的间隙以及刷毛齿形，分析了这些结构参数对密封性能的影响规律。
Select the Dodge Tool from the Toolbar, then right-click anywhere on the canvas and set the brush Master Diameter to 455px.
在工具箱中选择减淡工具，然后在画布任意位置右击鼠标，设置画笔大小为455px。
The settings you use are going to vary with each line you create, especially the diameter. Below shows one Brush Tip Shape I used.
笔刷的设置要随着你使用线条的不同分别进行设置，尤其是直径。下面显示的是我使用的一种画笔笔尖的形状。
Select the Brush Tool, set the diameter to 400 pixels.
选择画笔工具，设置直径为400像素。
In the brush Shape Dynamics Window change the Control from Fade to Pen Pressure, and the Minimum Diameter to 1%.
在笔刷形状动态窗口改变“渐隐”到“钢笔压力”，并且最小直径设置成1%。
The Settings you use are going to vary with every line you produce, specially the diameter. Below exhibits one Brush Tip Form I utilized.
笔刷的设置要随着你使用线条的不同分别进行设置，尤其是直径。下面显示的是我使用的一种画笔笔尖的形状。
In the brush Shape Dynamics Window adjust the Manage from Fade to Pen Pressure, and the Minimum Diameter to 1%.
在笔刷形状动态窗口改变“渐隐”到“钢笔压力”，并且最小直径设置成1%。
Big diameter pipe can be composed of several round steel brush together, at both ends with wire tightly, within the lumen pull brush back and forth, until the metal color, reoccupy cotton brush clean.
大管径管子可由几个圆钢刷组装在一起，两端用铁丝扎紧，在管腔内来回拉刷，直至露出金属本色，再用棉纱拉刷干净。
Deburring polishing tools brush in diameter than the choice, generally by processing aperture big 5 ~ 15% can.
去毛刺抛光工具刷在直径的选择上，一般比被加工孔径大5 ~ 15%即可。
For this purpose, the bristles of the portions with the small diameter D2 of the polishing brush (20) are stiffened with resin.
为此，用树脂加固构成抛光刷(20)中的小直径D2的部分的毛状材料。
The result shows that the nano-particle surface charge is negative and its diameter distribution is more wide in brush plating solution.
实验结果表明纳米颗粒在镀液中荷负电，其粒径分布较广；
The diameter of the brush head, length and POM (POM) tube inner diameter, outside diameter, length, color can be according to customer requirements processing production.
刷头的直径、长短及POM(聚甲醛)管的内径、外径、长短、颜色都可以按照客户的要求加工生产。
Pick up a big brush (master diameter around 470, hardness 0) and brush round the right part of the selection as I did creating a white reflection.
选择一个大笔刷(直径大概470左右，硬度为0)，沿选区的右半部份绘制反射。
Brush 10-inch-diameter springform pan with oil.
在直径为10英寸的弹簧扣模平底盘上刷油。
Create another layer. With the same selection and same Brush with 70px Diameter, click once at the same spot.
创建另一个层，用同样的选区和70px直径的相同画笔，在相同位置点击一次。
Create another layer. With the same selection and same Brush with 70px Diameter, click once at the same spot.
创建另一个层，用同样的选区和70px直径的相同画笔，在相同位置点击一次。
应用推荐