Partition Panel, Side Mold, Bottom Mold.
隔板，边模，底模。
Under traveling magnetic field, casting ZL102 aluminum alloy thin-section castings' best process is: using stainless steel as bottom mold, voltage is between 220v-235v.
最终得到移动磁场下铸造ZL 102薄壁件的最佳工艺条件为：不锈钢底模，电压为220v- 235v。
The plant receives water from a small try at the bottom, which discourages mold growth and lightly humidifies the air.
植物通过底部的特殊处理吸收水份，阻止霉菌生长，稍微增加空气的湿度。
She is in a painting phase, and the people she paints are all the color of mold, look like they've just been dredged from the bottom of a lake.
她在学画画，她所画的人物类型都是同样的模式，看上去他们就像刚刚从湖底打捞上来的。
The bottom line is that it's senseless to spend time and money finishing a basement if leaks or moisture will ruin your work or cause mold to grow.
但是如果渗漏或湿气很严重，可能毁掉装修或者长霉菌，那就没必要装修了。
Die flat, mouth upward, from top to bottom directly into the mold.
模具平放，口向上，由上到下直接进入制粒模具里。
Another possible cause for odor is the build up of slime, mold, hair, etc in the tailpiece (the portion of pipe that comes out the bottom of your sink) or overflow of your sink.
另一个可能的原因是，建立气味煤泥、塑造、毛发、在尾翼等(部分管出来的底层你下沉)或溢流贵沉。
With the slab divider mold, be sure to line the bottom of the mold with freezer paper.
使用这些厚隔片的模具，请确保这些隔板的底部都铺上了冷冻纸。
To transport convex mold and heated setting mold, above them there are some intervals, every bottom of concave groove has hole connected with the interval.
转移凸模和热定型凸模上方设有空腔，其各个型腔底面设有气孔与空腔连通。
Channel bottom is welded into the frame, steel structure for the flat panel, and its size corresponds with the mold box.
底板是以槽钢焊接成框架，钢板为面板的平板结构，其尺寸与模框相对应。
Reserve some slices for placing on top of the nutella filling which will be the bottom of the cake when removed from the mold.
记得预留出一些盖到慕斯馅上面，出模后翻过来时便成了蛋糕底了。
In case the mold cannot be installed from the machine top because of the height limit of the clean room, a higher mold can be assembled and disassembled by the bottom upward way easily.
当由于洁净室高度的限制，使得模具无法从上方安装时，从下往上的安装方式可以实现更高的模具的拆装，不影响生产。
The bottom chassis covers the mold frame and includes a first opening.
底壳覆盖模制框架并包括第一开口。
Mold to form a mold box with the bottom, stirred slurry by pouring foam and resting, the initial setting process of making the green body can be cut.
模框与底板形成一套模具，搅拌好的浆料通过浇注发泡、静养、初凝过程使之成为可以切割的坯体。
The driving circuit substrate is disposed between the mold frame and the bottom chassis, and includes a circuit component.
驱动电路基板设置在模制框架和底壳之间，并包括电路元件。
Mold frame and floor flatness requirements of strength and high quality standards reach the bottom of the mold box and a direct impact on the production of aerated concrete yield.
模框和底板的强度及平整度要求很高，达不到质量标准的模框和底板直接影响加气混凝土生产的成品率。
Mold frame and floor flatness requirements of strength and high quality standards reach the bottom of the mold box and a direct impact on the production of aerated concrete yield.
模框和底板的强度及平整度要求很高，达不到质量标准的模框和底板直接影响加气混凝土生产的成品率。
应用推荐