• Sets the system boot list order.

    设置系统引导列表次序。

    youdao

  • Correct the boot list on each LPAR.

    纠正每个LPAR上的引导列表。

    youdao

  • I noticed that the boot list on each VIOS had changed.

    我注意到,每个VIOS上的引导列表改变了。

    youdao

  • No reconfiguration (apart from the boot list) was required, even for the VIOS.

    不需要重新配置(引导列表除外),即使对于VIOS也是如此。

    youdao

  • Create a new boot image on hdisk0 and add it to the boot list, as seen in Listing 10.

    在hdisk0上创建一个新的启动镜像,并将它添加到启动列表上,如清单10所示。

    youdao

  • Then, from the boot list option, you select the device from which the installation will take place.

    然后,在引导列表选项中选择要执行安装的设备。

    youdao

  • Again, we also need to check the boot list and recreate the boot image for this now non-mirrored volume group.

    同样地,我们仍需要检查引导列表并为现在这个非镜像的卷组重新创建引导映像。

    youdao

  • To ensure that the boot disk and boot list had been configured correctly, I would reboot the system to verify.

    为了确保引导磁盘和引导列表已被正确配置,我将重新引导系统以便验证。

    youdao

  • Configure and ensure the boot list is pointing to the standby BOS as the first boot device, as shown in Listing 17.

    配置并保证启动列表将备用BOS作为第一启动设备,如清单17所示。

    youdao

  • Instead of re-mirroring rootvg (above), we would change the boot list to point at the previous rootvg disk (old_rootvg) and reboot the LPAR.

    我们无需重新镜像(上面的)rootvg,相反,我们将更改启动列表以指向前一个root vg磁盘(old _rootvg)并重新启动LPAR。

    youdao

  • Verify in the LSI configuration utility that the daughter card is enabled and included in the boot list, preferably as the first boot device.

    通过LSI配置实用程序检查子卡是否已经启用并包含在引导列表中,子卡最好是第一个引导设备。

    youdao

  • As a pre-cautionary measure, we verify that rootvg is now mirrored, include the new disk in the boot list and create a new boot image for the mirrored volume group.

    作为一种预先的防范措施,我们验证了rootvg现已被镜像、在引导列表中包含了新磁盘并为所镜像的卷组创建了新的引导映像。

    youdao

  • After making these changes, it was important that I re-create the boot image, check the boot list contained only the new hdisk and that the primary dump device was set correctly.

    在进行了这些更改后,需要重新创建这个引导映像、确保引导列表只包含新的hdisk且主转储设备已正确设置。

    youdao

  • After making these changes, it was important that I re-create the boot image, check the boot list contained only the new hdisk and that the primary dump device was set correctly.

    在进行了这些更改后,需要重新创建这个引导映像、确保引导列表只包含新的hdisk且主转储设备已正确设置。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定