Cemented carbides cutter blade wear slightly, its main wear mechanism is separation of transferred film.
硬质合金刀片的磨损缓慢，其磨损主要是由于刃口上高分子转移膜脱落引起的。
The FXF type non-rotating stabilizer (rubber sleeve stabilizer )is a special tool in drilling to avoid blade wear and wall damage.
FXF非旋转稳定器（橡胶套稳定器）是钻井作业中为保护井壁不受刮削而制作的专用工具。
Boneless Sheffield pursuit and aerodynamics, eliminate the perfect combination of high-speed car when the wind caused the movement of glass, make jitter blade wear to a minimum.
无骨雨刷追求与空气动力学的完美结合，彻底消除汽车高速行驶时由于风力造成的运动造成的运动抖动，使刮片对玻璃的磨损降到最低。
Heavy reinforcing with rebar also tends to slow the blade and make it wear faster.
重型加强与钢筋也就会减缓刀片，使其磨损更快。
Some explosion-proof tools use some wear and incomplete after, especially with the blade explosion-proof tools, or serious damage, should not continue to use, should be timely into the trash.
有的防爆工具使用过后有些磨损和残缺，尤其带刃的防爆工具，或严重损坏，不应在继续使用，应及时打入废品。
The segments that are attached to the blade must be wider than the core, otherwise the blade core will wear quickly and render the diamond blade useless.
隶属的部分，叶片必须大于核心否则核心将穿叶片很快使钻石刀无用。
From the outside of the seal of the pollutants permanent embedded seal on the blade surface and cause shaft sealing lip premature wear of margin;
污染物从密封的里外面永久性的嵌入密封刃口上造成轴表面和密封唇缘的过早磨损；
Always wear protective gloves while handling the blade.
在更换刀片的时候始终配戴防护手套。
The research is an important meaning for designing moving blade and researching wear rule on chopper.
这项工作对动刀片刃口形状的设计和磨损规律的研究具有一定的指导意义。
The number of rubber strip. The other, when the wiper wiper is not complete, can also purchase a wiper blade corrector, friction rubber parts and rain wiper blade, the irregular wear part corrected.
别的，当发现雨刮器刮水不完全时，也能够采购一种雨刮片修正器，夹着雨刮片的橡胶部位磨擦，使其不规则磨损的部分得到修正。
Based on the inspection and analysis to the imported wear resisting components, the cutting blade and end bit of model D9L bulldozer were made using air cooled cast steel.
在检测分析进口抗磨件基础上，采用空冷贝氏体铸钢制造了D9L推土机铲刃、铲角。
Dividing blade is mainly used for paper, film, gold, silver foil, aluminum, copper films, tapes and other items for dividing, asking for the least cutting resistance, the largest wear resistance.
分切刀片主要用于纸张、薄膜、金、银箔、铝箔、铜箔、磁带等物品的分切，要求刀片切断阻力最小，耐磨损性最大。
The ginger like Sorbite forming mechanism and the high wear resistance of ginger like carbide cutter blade were studied in this paper.
本文从空间形貌上说明姜块状碳化物的形成机制，并从微观机理分析姜块状碳化物提高刀片耐磨性的原因。
Through research on the influence of the peripheral speed of diamond saw blade upon the wear of diamond cutting segments, this paper deals with the wear mechanism of the same.
本文通过研究金刚石锯片线速度对锯齿磨损的影响，探讨了金刚石锯齿的磨损机理。
This paper described the grit wear mechanisms of abrasive belts when grinding blade material (1cr13).
本文探讨了磨削叶片材料(1cr13)时砂带的磨损机理。
This method of production means that the sword or knife is stronger as it is a solid construction rather than a blade fixed to a base which can come off through wear or contact.
这种生产方法意味着刀剑或匕首因其坚固的结构，而比刀刃固定在刀座上更结实，后者在佩带或使用时可能脱落。
A high strength cast steel wear resistant material for cutting blade material for leveling machine has been developed.
研制了一种高强度平地机刀片铸钢耐磨材料。
The wear performance of the thin blade was compared to that of a normal blade.
并就金刚石薄锯片的耐磨性与常规锯片进行了比较。
The blade in the intermediate shaft adopts box plate type structure, to improve production efficiency; the blade adopts Q345 wear-resistant material, to extend the service life.
中间轴上叶片采用箱板式结构，提高生产效率，叶片材质采用Q 345耐磨，延长使用寿命。
For surfacing welding or repair the wear out face made by low carbon steels and middle carbon steels, as axle, gear and blade of mixer.
堆焊或修复低碳钢、中碳钢及低合金钢磨损表面如车轴、齿轮和搅拌机叶片等。
High precision of production process, good blade parts processing, long life! High wear resistant property.
高精度制作生产工艺，刀口部位加工优良，寿命长高耐磨性能强。
Scraper with double-sided knife with high-strength wear-resistant materials, board, according to the different soil hardness, the control point of the blade buried.
刮板带双面用高强度耐磨材料刀板，可根据土壤硬度的不同，控制铲刀入土角度。
The article put emphasis upon the introduction of circular saw blade research, band saw blade research, wear and erosion of cutting tool, the new technique in aspects of timber milling c...
文章着重介绍了圆锯片研究、带锯条研究、刀具磨损和腐蚀、木材铣刀方面的新技术及木材高速切削的一些研究成果，综述了刀具设计和刀具磨损方面新的研究理论。
The article put emphasis upon the introduction of circular saw blade research, band saw blade research, wear and erosion of cutting tool, the new technique in aspects of timber milling c...
文章着重介绍了圆锯片研究、带锯条研究、刀具磨损和腐蚀、木材铣刀方面的新技术及木材高速切削的一些研究成果，综述了刀具设计和刀具磨损方面新的研究理论。
应用推荐