Some researchers think they may have broken this limit, and the implications are mind bending.
可是某些研究人员却认为，他们可能已经打破了这个极限，然而其含意却是离奇古怪令人费解的。
Bending fatigue limit stress is still short of reliable data for gear of domestic material in gear design mostly used are the data offered from ISO6336.
在齿轮设计中，国产材料齿轮的弯曲疲劳极限应力仍然缺乏可靠的试验数据，大多是沿用ISO 6336提供的数据。
The main function of the system is in-plane bending radius estimation, forming limit estimation and forming process optimization.
本系统的主要功能有：面内弯曲半径的预测；成形极限的预测；成形工艺的优化。
Clearance between tube and various dies is of great importance to influence forming limit and quality during thin-walled nc bending process.
管材与不同部位模具间隙是影响薄壁管数控弯曲过程成形极限和成形质量的重要因素。
The mandrel(including flexible balls) is the key to improving the forming limit and forming precision in thin-walled tube NC bending process.
薄壁管数控弯曲中带芯头的柔性芯模是提高薄壁管件成形极限和成形精度的关键因素。
It is researched that the bending behaviors of external prestressed composite steel-concrete beams in service ability limit state.
研究了体外预应力钢-混凝土组合梁在正常使用极限状态下的受弯性能。
Through the stress field intensity approach, the relationship between the rotary bending fatigue limit and torsion fatigue limit was studied.
根据应力场强法，分析了旋转弯曲疲劳极限与扭转疲劳极限之间的关系。
Using present bending fatigue limit data of gear tooth and other materials of gears, the calculating method of re liability is proposed for bending strength of gear tooth st steady condition.
利用现有齿根弯曲疲劳极限应力数据及其它齿轮资料，提出了稳定工况下齿轮齿根弯曲强度可靠度计算方法。
It is proved that the optimality conditions are also sufficient if the objective function is a convex function of the plastic limit bending moment.
当目标函数是塑性极限弯矩凸函数时，证明了这一最优性条件也是最优解的充分条件。
After strengthening by the steel plate, the - beams gain the better bending stiffness, higher limit load-bearing and flaw of the beam can be controlled soundly.
经粘钢加固后的钢筋混凝土梁具有极限承载力高、抗弯刚度大的优点，裂缝开展也得到有效的控制。
Deformation mode is adjusted according to forming limit diagram (FLD) and maximum springback error, so the optimized one can be found, which in turn optimizes the stretch bending trajectory.
根据成形极限图和规定最大回弹超差量来调整变形模式，找到优化的变形模式和拉弯轨迹。
This paper describes the limit analysis of latticed columns made from concrete-filled steel tubes under combined bending and axial loading.
本文用极限平衡法求解了钢管混凝土格构柱在轴力和弯矩共同作用下的极限承载能力。
The limit load calculation of welding piping tees under the action of the in plane bending moment was derived based on the limit analysis.
基于极限分析的观点，推导了工业中焊制三通在面内弯矩作用下的极限载荷估算式。
The limit bending capacity of a round-corner-rolled crankshaft is measured with the testing machine.
利用该试验机对日本大发公司生产的经过圆角滚压处理的曲轴的极限承载弯矩进行了测试。
An equation to calculate concrete diaphragm walls bending moment is deduced based on the crack control limit value.
推导了由裂缝控制限值反算地下连续墙弯矩的计算方法。
The result showed that the bending moment would had great influence on the limit lateral capacity of the masonry wall.
结果表明弯矩对墙体抗侧承载力有很大的影响。
In bending failure test pieces, after crack chemistry grouting, the bending rigidity slightly has increased, but the limit load-carrying capacity has no obvious variety.
正截面试件，裂缝灌浆后刚度略有提高，但极限承载力无明显变化。
In bending failure test pieces, after crack chemistry grouting, the bending rigidity slightly has increased, but the limit load-carrying capacity has no obvious variety.
正截面试件，裂缝灌浆后刚度略有提高，但极限承载力无明显变化。
应用推荐