Moreover, the interaction between the membrane and polymer chain length, and the effects of bending rigidity and surface tension on the deformation of the membrane are investigated.
此外，考察了膜和高分子链段之间的相互作用，高分子链长以及膜的弯曲刚性、张力对膜形变的影响。
In bending test, the spring constant of AFM micro cantilever is corrected through the calibration of its effective length.
在弯曲测试实验中，通过标定测试用AFM微悬臂梁的有效长度，从而修正了其弹簧常数。
It is proved that the main affecting factors include: equivalent pile length, bending stiffness of abutment, ratio of width to span, distance of webs, etc.
整体式桥台的等代桩长、桥台纵向抗弯刚度、宽跨比及箱梁肋板间距等，是影响该类桥梁剪滞系数的主要因素。
With this situation, any amount of axial load can be applied to compressive bar of arbitrary length without bending.
在此状态下可在任意长度的压杆上，加任意大小的轴向载荷，而不产生弯曲。
In the process of bending, the excessive length of the straight flange of the bend mold and the workpiece with turnups cladding the lower mold support make a comparatively difficult unloading.
在工件折弯过程中，当工件直边长度尺寸较大且工件上带有翻边时，工件包覆在下模架上卸料比较困难。
The testing result of present test method of body bending on seat is influenced largely by leg length of testee's and the efficiency is comparatively low.
目前我国体质测量中，现行的坐位体前屈测量方法的测量成绩受被测者下肢长度影响较大，测量的有效性较低。
The result showed that shot size and gas delay time were the primary factors influencing gas penetration length, bending strength and fingering.
结果表明，欠料注射量和延迟时间是影响气腔长度、手指效应和弯曲强度的主要工艺参数。
Screw pump screw length is larger because of the job, poor rigidity, easy to cause bending work properly.
螺杆泵因工作螺杆长度较大，刚性较差，容易引起弯曲，造成工作失常。
The bending technology of the thick-wall supprt of aluminum alloy was analyzed, and the flattening length of bending, blanking force, piercing force and bending force were calculated.
分析了铝合金厚壁支座的弯曲工艺，计算了弯曲件的展开长度、落料力、冲孔力及弯曲力，阐述了弯曲件的回弹因素及凸凹模之间的间隙，介绍铝合金厚壁支座弯曲模具的结构设计。
The influence of hair fibre with different mix amount and length on the bending strength of cement were studied experimentally and the optimum mix amount and length have been found.
通过实验研究了不同掺量、不同长度的毛发纤维对水泥抗折强度的影响，找出了最佳长度和最佳掺量。
The elastic property of DNA is characterized by the elastic rod and filament approximately when its length is almost equal to the bending persistence length.
当其长度和刚性长度相近时，其弹性性质可以由弹性杆或弹性细丝来近似描述。
I think the maximal length of such a bending brake is pretty much what I have built: 50 ". The plans point this out too, but only after building it I also believe it."
我认为，最大的长度，例如弯曲制动器是漂亮得多，我有建：50“，使该计划指出这一点过分，但只有经过建设，我也相信这一点。”
The application of stamping technology to the length shearing technique used on the production line of cold-bending section steel was introduced.
介绍了一种冲压模具技术在复杂断面冷弯型钢生产线上定尺切断技术的应用。
CNC Hydraulic Press Brake offers "Conic Bending" up to a maximum of15 mm along the whole length.
电脑数控液压式折弯机提供“锥形折弯”全长尺寸最大可达到15毫米。
In this article author puts emphasis upon the discussion about distribution regularity of roll flattening along the length of roll body and optimum roll-bending force, which is of certain value.
本文重点讨论轧辊弹性压扁沿辊身长度分布的规律及最佳弯辊力，有一定参考价值。
Steel tube length or double length delivery, for steel pipe bending degree requirements.
钢管以定尺或倍尺交货，对钢管弯曲度有一定要求。
Takada's simplified formula calculates the length of the start-bending point to the fault according to Kennedy's method and the soil constraint is not considered in his finite element model.
Takada简化计算公式采用Kennedy方法计算弯曲点到断层的距离，其有限元模型中并没有考虑管周围土作用。
Takada's simplified formula calculates the length of the start-bending point to the fault according to Kennedy's method and the soil constraint is not considered in his finite element model.
Takada简化计算公式采用Kennedy方法计算弯曲点到断层的距离，其有限元模型中并没有考虑管周围土作用。
应用推荐