• Springback is one of the main problems which influences the quality of bending and should be considered at the stage of designing the bending die and process.

    回弹是影响弯曲件成形质量的主要因素之一,是弯曲模具和弯曲工艺设计要考虑的关键问题之一。

    youdao

  • Company's main products are: Domestic bending die.

    公司主要产品有:国产折弯模具。

    youdao

  • The practical structure of a precision bending die with a turning block is presented.

    介绍了翻转模块式精密弯曲模的实用结构及模具工作过程和结构特点。

    youdao

  • The main contents and results are as follows: Firstly, the push bending die and the hydraulic system are designed.

    主要研究内容和结果如下:首先设计了推弯成形模具和液压系统。

    youdao

  • Through analyzing copper bus-bar structure and forming process, designed a reasonable and highly effective bending die.

    通过分析铜排结构及成形工艺,设计出了合理、高效的扭弯模具。

    youdao

  • A practical structure for the bending die with an automatic stripping mechanism for forming the snap springs is introduced.

    给出了卡簧弯曲自动卸件模实用结构,介绍了模具工作过程和结构特点。

    youdao

  • The structure, operating principle and main design points of the hopper-type automatic-feeding bending die used on a general stamping machine are stated.

    介绍了在通用冲床上使用的漏斗式自动送料弯曲模的结构形式、工作过程和设计要点。

    youdao

  • A practical structure of slide plate type of bending die has been presented for forming of ring parts with description of the operating principle of the die.

    给出了弯制环形零件的滑板式弯曲模实用结构,论述了模具工作原理。

    youdao

  • The practical structure of a precision bending die with a turning block is presented. The working process and structure characteristics of the die are described.

    介绍了翻转模块式精密弯曲模的实用结构及模具工作过程和结构特点。

    youdao

  • The structure and working principle of a bi_directional bending die were introduced. And the points for attention in design and manufacture of the die were listed.

    介绍了双向弯曲(翻边)成形模的结构及工作过程,指出了模具设计、制造时应注意的事项。

    youdao

  • It is so difficult to get non-scrape surface using ordinary bending die. Thus a new bending die structure is provided, and its forming process is analyzed as well.

    用一般的折弯模很难达到不擦伤表面,对此,提出了一种新的折弯模结构,并分析了其成形过程。

    youdao

  • The top die is the important component of the complete set of pipe-bending die, the design of which directly impact the bending quality and the bending efficiency.

    顶模是弯管全套模具的重要部件,它的设计直接影响弯管质量和弯管效率。

    youdao

  • Through the design of bending die for the back hoop of silencer, die design analysis and die structure for large cylinder part considering springback compensation was introduced.

    通过对消音器后环箍弯曲成形模的设计,介绍了考虑弹复补偿后,较大圆筒件成形模具的设计分析和模具结构。

    youdao

  • The bending process design, bending process parameters' calculation and selection, and bending die structure design for the forming of fixed board were all introduced in this paper.

    介绍了弯曲件的弯曲成形工艺方案、工艺参数的计算与选取以及弯曲模具结构与设计,得出采用多道弯曲成形工序是合理的。

    youdao

  • The technological property of the fixing plate of the condenser was analyzed. The structure characteristics and working process of the bending die for forming the part were introduced.

    分析了冷凝器固定板的工艺性,介绍了该零件弯曲成形模的结构特点和工作过程。

    youdao

  • The structure and stamping technology of glass bracket were elaborated. At the same time, the blanking die, bending die for one time and bending die for two times were also introduced.

    叙述了玻璃托的零件结构及成形工艺,介绍了落料压凸模、一次弯曲模和二次弯曲模的模具结构及设计要点。

    youdao

  • Aimed at the difficulties in the bending forming of punching parts, the bending die with dual-punch is designed, the complex shape of this part is once formed by the ordinal action of dual-punch.

    针对该冲压件弯曲成形难的问题,设计了双凸模弯曲模,通过双凸模的依次动作可一次成形该零件的复杂形状。

    youdao

  • Aimed at the difficulties in the bending forming of punching parts, the bending die with dual-punch is designed, the complex shape of this part is once formed by the ordinal action of dual-punch.

    针对该冲压件弯曲成形难的问题,设计了双凸模弯曲模,通过双凸模的依次动作可一次成形该零件的复杂形状。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定