Since a bending force is exerted on the pipe during break out, the tool joint connection must be set in the slips as low as possible.
由于卸扣会使钻具产生弯曲力，因此，钻具接头必须尽可能低些坐在卡瓦上。
The influence of work roll′s bending force on roll′s bending deformation, roll gap geometry and exit thickness is investigated under the conditions of different width and thickness of sheet.
研究了不同宽度和厚度下工作辊弯辊力对辊系变形、辊缝形状及轧件出口厚度的影响规律。
Because force is generated with help from the ground, bending your knees places your body in better position to produce trunk, hip, and shoulder rotation.
因为力量源自地面，弯曲你的膝盖能让你的身体处于一个更易通过躯干，髋和肩部转动获得能量的绝佳位置。
A new model of rub impact force considering varied rotating speed was derived and the rub impact response of a rotor system with initial bending and asymmetric stiffness was analyzed.
建立了考虑转子转速的新的碰磨力模型，分析了具有初始弯曲和刚度不对称转子系统的碰磨响应，得到了系统参数对系统分叉和混沌响应的影响。
Loading plastic soils into bending is an effective method of causing soil fracture with both minimum force and energy requirements.
弯曲加载是需要最小力及最少能耗使塑性土壤破碎的一种有效的加载方式。
Pumps work, as the two screws driven screw symmetrical and active engagement, so the role of the active radial force on the screw entirely balanced, active screw does not bear bending loads.
泵工作时，由于两从动螺杆与主动螺杆左右对称啮合，故作用在主动螺杆上的径向力完全平衡，主动螺杆不承受弯曲负荷。
The theory and method of bending test on nanobeam for the measurement of Young's modulus based on atomic force microscope (AFM) are introduced.
阐述了基于原子力显微镜(afm)的弯曲测试测量纳米梁杨氏模量的理论和方法。
In space structure, the socket joint systems can be subjected to different ratios of axial force and bending moment.
在空间结构中，碗式节点往往在不同比例的轴力和弯矩共同作用下工作。
The glass fiber reinforced plastic material prepared by the above process has high mechanical strength, large shearing force and bending strength, and good abrasion resistance.
由上述工艺制备出的玻璃钢材料具有机械强度高、剪切力和抗弯强度大和良好的耐磨性能。
Axial force has a great effect on deformation of rod or tubing with initial bending stress.
轴向力对具有初弯曲的杆(管)柱变形影响很大。
When displacement and force iterative formulae are derived, the bending deformation and shearing deformation are taken into account.
文中推导了位移及力的迭代公式，其中考虑了多阶剪力墙的弯曲变形及剪切变形。
The effect of the vertical force on the pier stiffness and the interaction among the level, bending and torsion displacement is also studied.
文中考虑了竖向力对群桩刚度的影响以及桩基承台水平位移与弯曲、扭转位移的耦合作用。
The force with process of bending pipe has been quantitatively and qualitatively analyzed in the theories of elasticity mechanics and plasticity mechanics.
运用弹性力学与塑性力学理论，对常用弯管工艺过程进行受力分析。
The atomic movement of the cantilever beam was motivated by transverse force on one end while another end was fixed, through which its bending deformation image was obtained.
通过一端固定另一端施加横向作用力驱使原子运动，得到纳米单晶铜悬臂梁弯曲的变形图。
The industrial trials of the online shape control models which include roll configuration, and bending force preset calculation were carried out.
完成了包括辊型配置和弯辊力自动设定等的板形在线控制工业试验。
Relatively comprehensive test study on the strength capacity of the reinforced concrete beam under bending moment, shear force and axial tensile force was carried out.
对弯、剪、轴拉复合受力状态下钢筋混凝土梁的承载能力进行试验研究。
In the thesis, the contact stress, bending stress on the root and the contact force on the tooth have been calculated by Finite Element Method (FEM).
文章采用有限元接触计算方法，计算了螺旋锥齿面接触应力和齿根弯曲应力以及齿面接触合力。
The lower balance force with balance factor 0.89 is adapted to reduce bending of universal coupling shaft and load of copper slider.
提出接轴平衡力应该采用欠平衡，平衡系数取0.89，这样既可以降低接轴承受的弯矩，又可以降低接轴虎口铜滑块的载荷。
By determining rational fulcrum and force bearing point, and applying bending torque to cause the plastic deformation of the steel pipe, it can realize the cool bending of the pipe.
这种弯管机由钢制机架、下模、上模、夹具、液压系统和内胎等组成，其工作原理是通过确定合理的支点和受力点并施加弯曲力矩，使钢管发生塑性变形，实现钢管的冷弯曲。
A motion law of the disintegrative units is obtained by analyzing the internal force and bending moment of the architectural units.
通过分析建筑物构件的内力和弯矩，得到了建筑物解体时构件的运动规律。
Backbone and four limbs: physiological bending of backbone, no tenderness or vertical percussed pain. Free movement of four limbs. Normal muscle force and muscle strength.
脊柱四肢：脊柱呈生理弯曲，无压痛及纵向叩击痛，四肢活动自如，肌力及肌张力正常。
It can be used to compute in one run the secondary bending moments due to both elastic and creep strains, produced by prestress force.
它可以一次算出预加力引起的弹性的和混凝土徐变的次弯矩。
Finite Element Method is used to calculate the maximum bending moment and axial force of lining and its deformation.
利用有限元法计算了考虑衬砌接头和不考虑衬砌接头两种情况下衬砌的内力和衬砌的变形。
This paper analyses the relativity between bending moment (M) and axial force (N) in calculating ground supporting capacity, and the effect of relativity on reliability calculation.
分析了在地基承载力验算中，弯矩M与轴力N之间相关性的存在，以及相关性对可靠度计算的影响。
With the limitations of the maximal bearable bending moment and the positive lifting force, the controlling parameter curves of span and lifting Angle are then acquired to guide the safety operation.
以长桩结构能够承受的最大弯矩和吊点力不为负值作为限制条件，得出安全作业跨距和倾角参数控制曲线。
For ring beam bracing system, irregular bracing arrangement may cause uneven force and large bending moment that in turn affects the ring beam bracing system.
环梁支撑系统，不规则的支撑安排可能会导致不平衡力和弯矩大，反过来又影响了环梁支撑系统。
Fiber model beam-column elements are presently one of the most practical and efficient element models handling biaxial bending and variable axial force coupling problems of frame structures.
纤维模型梁柱单元是目前处理空间杆系双向弯曲与变轴力耦合问题最为实用有效的单元分析模型。
The Young's modulus of silicon nano-beam on <100> direction was measured by bending test method using an atomic force microscope(AFM).
阐述了基于原子力显微镜（AFM）的弯曲测试测量纳米梁杨氏模量的理论和方法。
The Young's modulus of silicon nano-beam on <100> direction was measured by bending test method using an atomic force microscope(AFM).
阐述了基于原子力显微镜（AFM）的弯曲测试测量纳米梁杨氏模量的理论和方法。
应用推荐