When Thomas had eaten all the cherries, his father said to him, "My dear son, if you had bent down earlier to pick up that horseshoe, it would not have been necessary for you to bend so many times for the cherries."
当托马斯吃完所有的樱桃后，他的父亲对他说：“我亲爱的儿子，如果你早点弯腰捡起那只马蹄铁，你就不必弯那么多次腰去捡樱桃了。”
From a standing position, bend forward from the waist with your knees slightly bent, letting your arms dangle close to the floor.
从站立位置开始，弯腰，让手臂垂下，膝盖微微弯曲，让手臂接近地面位置。
Thousands of tiny hairs in the cochlea bend when exposed to the original sound vibrations. But those hairs can get stuck in a bent position.
耳蜗内有成千上万的细毛纤维，当声音声音震动传入时，这些纤毛便会弯曲并保持一定的弯曲状态。
Two months later he bent himself to the study of drawing and painting as others would bend to the plough.
两个月后，像其他人将躬身耕作一样，他躬身于绘画和油画研究。
When stainless steel is bent, the metal towards the outside of the bend is in tension and the metal towards the inside is in compression.
当不锈钢弯曲时，朝向弯曲外面的不锈钢被拉紧，朝向弯曲内面的不锈钢被压缩。
We have explained this being due to light in the red spectrum bending readily, so red light is bent first over the horizon by the gravity of Earth where light in the other spectrums is not so bend.
我们解释过这是由于红色光谱更容易弯曲，所以当其他光线还没怎么样时，红光首先由于地球的引力而沿着地球的曲线弯曲。
Fingers should be bent, the index finger, two joints, the first of which is to bend, the second joint is straight.
手指要弯曲，食指的两个关节，其中第一个是要弯曲的，第二个关节就是要直。
P The minimum diameter to which a bar is bent shall be such as to avoid bending cracks in the bar, and to avoid failure of the concrete inside the bend of the bar.
弯曲钢筋的最小直径处应避免弯曲裂缝，并避免在弯曲位置的钢筋混凝土破坏。
The horse is slightly bent round the inside leg of the rider but with a greater degree of bend than in shoulder-in.
马体围绕骑手的内方脚轻微弯曲，但比肩内的弯曲程度还大。
The ferrule portion is bent along the longitudinal axis to form a bend.
套圈部分沿着纵向轴线弯曲以形成弯曲部分。
Proper kicking you don't bend your knees too much, but there is a knee-bent particularly on the down beat.
正确的踢腿动作中你的膝盖不能太弯，但是膝盖是会有所弯曲的，特别是在向下踢腿时。
The upper and lower longitudinal edges of the metal sheet are bent to produce a first 'l' bend and a second 'chair' bend, respectively.
弯曲该金属板的上、下纵向边缘以分别形成第一“L”形弯曲和第二“椅”形弯曲。
Stand with knees bent slightly, feet at hip distance apart, toes forward. Knees should be directly over toes. Bend forward so upper body is parallel to floor.
膝关节微屈站立，双脚与髋同宽，脚尖向前。膝关节在脚尖正上方。身体前弯与地面平行。
Stand with knees bent slightly, feet at hip distance apart, toes forward. Knees should be directly over toes. Bend forward so upper body is parallel to floor.
膝关节微屈站立，双脚与髋同宽，脚尖向前。膝关节在脚尖正上方。身体前弯与地面平行。
应用推荐