The productivity of mill, separating indexes of dressing process are increased, and the consumptions of materials and power are decreased by adoption of the accurate method for ball load and addition.
新的装补球方法提高了磨机生产率及选别指标，并降低了球耗和电耗。
The hand - strong enough to hold a 14-stone load - is also so versatile that Matthew can grip a pen to draw pictures and write, tie his shoe LACES and catch a ball.
这只手足够强大，能够举起14石的负重，同时也功能多多，使得马修可以握住一支笔进行绘画和书写、绑鞋带和抓起一个球。
Single-row Angular Contact ball bearings can sustain radial, axial or composite loads, however, any axial load must be in one direction.
单列角接触球轴承可承受径向，轴向或复合负荷，不过，任何轴向负载必须在一个方向。
The guide rod and bearing system support the load while the ball screw drives the load.
该指南杆和轴承系统的负载，同时支持的滚珠丝杠驱动器的负载。
Two-way pressure has mounted on ball bearings between the shaft and two outer rings, in the middle ring and outer ring were added between the steel ball, able to withstand the two-way axial load.
双向压力球轴承有安装于轴上的中间圈和两个外圈，在中间圈与外圈之间分别加有钢球，能够承受双向轴向负荷。
Low torque required to drive the load due to high efficiency ball screw.
低扭矩所需的驱动负载，由于高效率的滚珠丝杠。
Ready-to-install ball type and roller type profiled rail units with high load capacity for machine tools.
准备安装的球型和异型滚筒式的铁路单位，高负荷能力的机床。
The higher the speed should not adopt thrust ball bearings available class bearings are subjected to purely axial load.
在转速较高不宜采用推力球轴承的情况下可用该类轴承承受纯轴向负荷。
Load locking spring prevents load from free falling in the event the ball bearings are lost from the nut.
负载锁定春季阻止自由的球轴承是从螺母丢失下降负荷。
The ceiling system should satisfy these requirements that using lower chord ball as fixed point, adapting space change of hyperboloid steel grid, grid settlement under snow load.
其天花体系要满足以屋面网架下弦球为固定点和适应双曲面的空间变化、网架雪荷载作用下沉、热胀冷缩等变形运动。
DB combinations, DF combinations and four-point contact, double row angular contact ball bearings can withstand radial and bi-axial load.
DB组合，DF组合及四点接触、双列角接触球轴承可承受径向和双向轴向负荷。
Deep groove ball bearing is inseparable bearing, mainly it can be subject to radial load and some axial load as well.
深沟球轴承属于不可分离型轴承，主要承受径向载荷，也可承受一定量的轴向载荷。
The testing method and data processing procedure for random load on the transmission system of a BED type ball mill with straight flow are presented.
介绍了直燃式双进双出钢球磨煤机传动系统随机载荷的测试方法及数据处理步骤。
Bearing a single row thrust ball bearings to the heart, which has at the same time to bear a greater bearing axial load and radial load capacity.
轴承采用了单列向心推力球轴承，这种轴承具有同时承受较大的轴向荷载和径向荷载的能力。
In other words, the Basic Dynamic Load Rating provides a basis of Life Calculations based on the size and type of ball screws.
换句话说，基本额定动载荷提供了一个基于丝杠类型和尺寸来计算寿命的基础。
Four-point contact ball earings used for rolling mill roll the oil tank to withstand the axial load.
四点接触球轴承多用于轧钢机的油辊箱以承受轴向负荷。
Experiments indicate that it can make the throughput increased clearly, and can make the ball consumption and load reduced clearly that the mill outlet is properly reduced.
试验表明，适当缩小出料口，处理量明显增加，而钢球消耗和负荷确明显减少和降低。
The influence law of clearance on load distribution of single row four-point contact ball slewing bearings is researched.
研究了游隙对单排四点接触球转盘轴承载荷分布的影响规律。
Ball bearing perform to fully swivel under load.
载荷下滚珠轴承能够充分旋转。
Single thrust ball bearing can be subject to the axial load from single direction.
单向推力球轴承可承受单一方向的轴向载荷。
Considering radial load, axial load, centrifugal force and gyroscopic moment acted on the ball bearing simultaneously, an analysis model based on quasi-dynamic method was set up in this paper.
本文利用拟动力学法，同时考虑径向负荷、轴向负荷、自身离心力以及陀螺力矩作用的影响，建立了高速滚珠轴承载荷分布的分析模型。
Deep groove ball bearings mainly take radial load as well as take moderate axial load.
深沟球轴承主要承受径向载荷，也可承受一定量的轴承载荷。
We use a "sponge rubber ball on-load cleaning system".
我们使用的是“海绵胶球带负荷清洗系统”。
Four pionts Angle contact ball bearing is separable bearing, it can be subject to bi-directional load and have the function of both single row and double rows bearings.
四点接触球轴承为可分离型轴承，可承受双向轴向载荷，并有单列和双列角接触球轴承的功能。
Thrust ball bearing is separable bearing and only can be subject to axial load.
推力球轴承能承受两个方向的交变轴向载荷。
Thrust ball bearings can bear radial load, lower speed limit.
推力球轴承不能承受径向负荷，极限转速较低。
An analysis of a type of angular contact ball bearing under given input power spectrum density is performed. The result demonstrate that the bearing is safe in any load direction.
以某种角接触球轴承为例，验证了其在给定输入功率谱密度下任意方向加载都安全。
Split Plummer block, whose cap and base can be separated, mainly bear radial load. It fits for self-aligning spherical roller bearings or self-aligning spherical ball bearing.
剖分式轴承座的上盖和底座可分手，首要承受径乡向载荷，合适于圆柱孔和圆锥孔的调心滚子轴承和调心球轴承。
Split Plummer block, whose cap and base can be separated, mainly bear radial load. It fits for self-aligning spherical roller bearings or self-aligning spherical ball bearing.
剖分式轴承座的上盖和底座可分手，首要承受径乡向载荷，合适于圆柱孔和圆锥孔的调心滚子轴承和调心球轴承。
应用推荐