The drive system is comprised of at least one balance shaft and a torsion bar.
该驱动系统包括至少一个平衡轴和一个扭力杆。
By the ends of century the upper bearing of the balance shaft were likely to have the diamonds.
由世纪两端轴承上的平衡轴有可能产生的钻石。
Design of the balance shaft and its bearing will have important influence on the system's reliability and operation.
平衡轴及其轴承的设计对系统的工作可靠性和使用寿命有重要影响。
Bearings are located between the first end of the torsion bar and the center bore of the balance shaft, to center the torsion bar within the balance shaft.
多个轴承位于该扭力杆第一端与该平衡轴中心孔之间，将该扭力杆置于该平衡轴的中心。
When you buy the balance machine, don't just ask how high can the speed of the machine, be sure to ask the big shaft when Steyr balance can reach the speed of.
你在购买平衡机的时候，不要只问机器能达到多高的转速，一定要问清楚平衡斯太尔等大传动轴时能达到的转速。
Dynamic balance accuracy of aeroengine main shaft bearing cage is of the utmost importance to bearing performance.
航空发动机主轴轴承保持架动平衡精度对轴承的性能至关重要。
They are particularly suited to low specific gravity applications where the back-to-back design and center bush provide natural axial balance and additional shaft support.
该类型泵特别适合于低比重介质的工况， 在这种情况下背对背的设计及中间衬套可以产生自然的轴向平衡和附加的轴支撑。
Test shows that proper shaft alignments, compensation capacity of the coupling and rotor dynamic balance etc. are essential to the noise control.
试验表明，转子间的对中状况、联轴器的补偿能力以及轴系的动平衡等因素对机组噪声有明显的影响。
The lower balance force with balance factor 0.89 is adapted to reduce bending of universal coupling shaft and load of copper slider.
提出接轴平衡力应该采用欠平衡，平衡系数取0.89，这样既可以降低接轴承受的弯矩，又可以降低接轴虎口铜滑块的载荷。
Main components: two-rotor, the body, the main bearings, shaft seal, balance and energy-conditioning Pistons.
主要部件：双转子、机体、主轴承、轴封、平衡活塞及能量调节装置。
By analyzing the experiment results, the CBN grinding wheel dynamic balance result, the precision of motorized spindle and the rigidity of the grinding wheel shaft are proved.
通过大量的实验验证了CBN砂轮的动平衡效果、电主轴振动情况以及砂轮架的振动情况满足设计要求。
Loosen two fasten bolts on the seat of driven gear shaft, put the pad of required height to keep the balance of support plate, and ensure the even cutting.
松开从动齿轮轴支座上的两个固定螺钉，垫上所需高度的垫片，以保持左进料托板水平，保证割料后的切条均匀。
A simplified raceway model of the shaft furnace was build based on the force balance at the raceway border and by considering the influences of flame temperature and effective raceway diameter etc.
基于回旋区边界上力的平衡，并考虑理论燃烧温度和有效直径等的影响，建立了同类型竖炉风口回旋区的简化模型。
And the main influencing factors are two, 1, the transmission shaft and the balance machine connection way. 2, balancing machine spindle processing accuracy.
而主要影响因素有两项，1、传动轴与平衡机的联接方式。2、平衡机主轴加工精度。
The paper introduces some methods for diameter compute, velocity measurement, tension control, the same shaft series twice motors control and load balance control of twin drive roll.
介绍了卷径计算、线速度测量、张力控制、同轴串联双电机控制、上下辊负荷平衡控制方法。
The results have shown that the torque tube unbalance is not a key factor in high speed dynamic balance, but effects the power shaft.
结果表明：测扭基准轴的不平衡量虽然不是转子高速动平衡的决定性因素，但影响到传动轴的动平衡。
The balance point: the balance point for a typical badminton racket lies on the shaft.
平衡点一般球拍的平衡点都位于其中杆上。
Fx and the role of fluid in the plunger on the pressure balance, Fy occurred while rotating cylinder to generate torque, rotating drive shaft 5.
Fx与作用在柱塞上的液压力平衡，Fy则产生使缸体发生旋转的转矩，带动轴5转动。
Unbalanced two-stage reciprocating inertia force can be balanced by using Lanchester's double-shaft balance system, so that the engine noise and vibration could be reduced notably.
采用兰氏双轴平衡系统，可以平衡二阶往复惯性力，使柴油机的噪声和振动明显下降。
And the Fuzzy-follower is applied in shaft bottom coal conveyor of a medium-sized coal mine and gives good results. Thus, it solves the problem of power balance of double-motor driving system.
该模糊跟随器在某中型煤矿的井下原煤运输系统中进行了实际应用，效果良好，较好地解决了双电机拖动系统的功率平衡问题。
The rocker arm is connected with the balance weight block through a rotary shaft, a cam, a pulley, a steel cable and a lifting rod, and an initial position can be selected through a barrier shaft.
摇臂通过转轴、凸轮、滑轮、钢丝绳、提升杆与配重块相连，初始位置可由挡轴选定；
The rocker arm is connected with the balance weight block through a rotary shaft, a cam, a pulley, a steel cable and a lifting rod, and an initial position can be selected through a barrier shaft.
摇臂通过转轴、凸轮、滑轮、钢丝绳、提升杆与配重块相连，初始位置可由挡轴选定；
应用推荐