Remove the upper suspension arm nut and bolt at the axle bracket.
从车轴支架上拆去上端悬吊臂螺帽和螺栓。
It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.
转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
It consists of steering wheel steering shaft worm gear sector pitman arm drag link steering knuckle arm king pin steering arms tie rod front axle and steering knuckle.
转向系统包括转向盘,转向轴,蜗杆,扇形齿轮,转向摇臂,直拉杆,转向节臂,主销,转向臂,转向直拉杆,前轴和转向节。
In the double control arm axle the wheel carrier is supported by two a-frame arms and a tie rod.
在双控制臂车桥中,车轮托架由两个三角形臂和一个横拉杆来支撑。
Loosen trailing arm on front-axle cross member and pull out of the mount.
松开前轴横梁上的拖臂并从支座中拔出。
The track rod length is set so that its connection to the track arm falls on an imaginary line taken from the king pin to a point on the vehicle center line just in front of the rear axle.
转向横拉杆长度的设置要保证转向横拉杆与转向节臂的连接点位于主销到后桥前端汽车中心线上的点所形成的假想连线上。
The track rod length is set so that its connection to the track arm falls on an imaginary line taken from the king pin to a point on the vehicle center line just in front of the rear axle.
转向横拉杆长度的设置要保证转向横拉杆与梯形臂的连接点位于主销到后桥前端汽车中心线上的点所形成的假想连线上。
Remove the lower suspension arm nut and bolt from the axle bracket.
从车轴支架上拆去上端悬吊臂螺帽和螺栓。
Position the lower suspension arm at the axle bracket and rear bracket.
从车轴支架上拆去下端悬吊臂螺帽和螺栓。
Applied with inverted power, the long axle drives the power arm and the long lever to fallback, accordingly the bed surface returns to the normal position.
施以反向动力,长轴带动动力臂和长杆回落,则床面回复原位。
With the dynamics calculation of complete vehicles, the effect of the axle box rotary arm positioning mode on resilient nodal points is analyzed.
通过整车动力学计算,分析了轴箱转臂定位方式对弹性节点的影响。
Obviously, a shorter bellcrank arm can be adapted with success if the bellcrank axle is moved aft so that the both control arms are almost parallel.
显然,在较短bellcrank手臂可以适应,如果成功的bellcrank船尾轴移动,使二者控制臂几乎平行的。
The shift arm aperture line shall aligned with the engine main axle center line, without any displacement.
排挡臂开口线与引擎轴心对齐,不可偏移。
Position the lower suspension arm at the axle bracket and rear bracket.
把下端悬吊臂放在车轴支架和后侧支架上。
It is one of trailing arm suspension that can only be applied in the rear axle and cannot be applied in the front steering axle, so there are only two wheel alignment parameters: toe-in and camber.
它属于纵臂式悬架,只能用于后轮,且不能用于转向轮,因此其定位参数只有车轮前束和外倾角两种。
The end surface of the positioning screw cap of the equalizing axle is matched with an equalizing axle shell or the end surface of a swing arm.
平衡轴定位螺盖的端面与平衡轴壳或者摆臂的端面相配合。
The end surface of the positioning screw cap of the equalizing axle is matched with an equalizing axle shell or the end surface of a swing arm.
平衡轴定位螺盖的端面与平衡轴壳或者摆臂的端面相配合。
应用推荐