Compared with as-welded specimens with no defects, the fatigue strength has been increased by 32%, and the fatigue life by 2~7 times.
与不含焊接缺陷的焊态试件相比,提高疲劳强度32%,提高疲劳寿命2~7倍;
Finally, the welding procedure has been proved to be feasible by as-welded appearance checking, magnetic powder inspection, ultrasonic inspection and radiographic inspection.
最后,本课题通过焊后的外观检测、磁粉探伤焊、超声探伤和射线探伤证明了焊接工艺规范合理可行。
Surfaces to be welded or thermally cut shall be cleaned of all foreign material such as grease, oil, dirt, scale, slag and paint that would be detrimental to either the weld or base material.
需焊接或热切割的表面应排除所有可能会损坏焊材或母材的杂物,如脂、油、灰尘、水垢、熔渣和油漆等。
As Flupac's technology does not involve heating or welding, the system is very flexible, fast to install and very reliable compared to conventional welded solutions.
福尔湃克管路技术无需任何加热或焊接,整个管路系统与传统的焊接管路系统相比是集灵活与便于快速拆装,高质量与高可靠性于一身的管路解决方案。
Welded pipe that bended by hot bending method with a set of specific die and welded by plasma arc welding method was used as tubular blank of SPF.
采用焊管作为管坯 ,焊管弯曲采用专用模具热弯 ,焊接采用等离子弧焊。超塑成形采用多层模结构 ,用模具来控制波形。
The flammable materials used as heat preservation, cooling, heat insulation and decoration could not be welded and scalpeled unless it fully adopts very effective fireproofing safety precautions.
在用可燃材料作保温、冷却、隔热、隔音、装饰的部位,未采取切实可靠的防火安全措施,不准焊、割。
The mechanism causing various defects in laser welded gears is studied as well.
分析了激光焊接齿轮所产生缺陷的机理。
The technology parameters selection, such as composition design, strip rolling and tube welding, of developing high strength atmospheric corrosion resisting welded steel tube are introduced.
介绍了唐钢带钢厂在开发高强耐候焊接钢管过程中,成分设计、带钢轧制及钢管焊接等技术参数的选取。
It is shown that under suitable welding condition, the alloy can be welded well by using TIG arc welding and the welding wire having the same composition as the alloy.
结果表明,在一定的焊接工艺条件下,使用钨极氩弧焊和与母材同质的焊丝,可以对ZA12材料进行有效的焊接。
After heat treatment, the residual austenite is decreasing and carbides are increasing. The hardness of the surfacing layer is higher than that as welded.
经过热处理后,堆焊层中残余奥氏体的量明显减少,碳化物进一步析出,使得堆焊层的硬度比焊态下有了较大的提高。
This paper introduces some concepts and calculation methods, such as primary qualification rate of welding, equivalent welded joint and qualification rate of equivalent welding.
介绍了焊接一次合格率、当量焊口、当量焊接合格率等概念及其计算方法。
This article introduces a kind of meter which can measure the misalignment and inclining of the welded head, and describes the principle and structure of the meter as well as its usage.
介绍了一种能测量焊头的偏移和倾斜量的仪器,阐述了仪器的原理和结构,描述了其使用方法。
Tailor welded blanks are defined as two or more sheets of blanks with equal or different mechanical properties, or surface coatings welded together by laser before stamping.
激光拼焊技术是将两块或多块具有相同或不同机械性能、不同表面状态的钢板使用激光焊接的方法连接成毛坯件,然后进行整体冲压成轿车结构件。
Materials for external attachments and vessel support welded directly to the pressure retaining parts shall be similar material as the pressure parts.
直接焊接到压力保持部件上的外部配件及容器支架的材料应与压力部件相同。
This article explained the correct application of the theory of strength through using the commonly used bevelled halving welded seam as an example.
以工程中常用的斜对接焊缝的研究为例,说明了力学强度理论的正确应用方法。
The lining (4) and the cable shield layer (10) are welded as a whole.
衬套(4)与电缆屏蔽层(10)焊接为一体。
The first peak load is lower slightly than the fracture load of adhesive bonded joints, and the second peak load is almost the same as the fracture load of the spot welded joints.
曲线上第一载荷峰值略低于单纯胶接接头的断裂载荷,第二载荷峰值与单纯电阻点焊接头的强度基本一致。
So, it is doubtful to directly use the J -integral as a fracture criterion in heterogeneous welded joints.
因此,在非均质焊接接头中直接应用J积分作为断裂判据不合适。
Aiming at these problems, taking D406A steel as an example, this paper systematically studied the fracture behavior of the ultra-high strength steel and it's welded joint.
针对这两种现象,本文以D406A钢为例,系统地研究了超高强度钢及其焊接接头的断裂行为。
Spiral welded pipe is a strip coil as raw material, often warm extrusion molding, to automatically double-wire submerged arc welding process double-sided spiral welded pipe joints.
螺旋焊管是以带钢卷板为原材料,经常温挤压成型,以自动双丝双面埋弧焊工艺焊接而成的螺旋缝钢管。
After welded pipes are treated by reducing tension mills known as "welded pipe seamless process". There are still some differences between welded pipe and seamless pipe in quality index.
焊管经张力减径机处理后有人称之为“焊管无缝化”,这种焊管与无缝钢管在一些质量指标上仍存在差异。
Flatness, as an important factor to evaluate the quality of outward appearance of welded joints, its compliance is directly related to train running stability and ride comfort.
平直度作为钢轨焊接接头外观质量的重要指标,其合格与否直接关系到列车运行平稳性及乘坐舒适性。
Gaseous NF3 containing 0.1% or less active fluorides (calculated as HF) was found to be noncorrosive toward several different parent and welded metal specimens.
含有0.1%或更少的活泼氟化物(认为是HF)的气态NF 3被发现对于几种不同的母材和焊接金属试验品是没有腐蚀性的。
Optimization design method of welded structure was put forward with welded joint fatigue damage as constraints.
提出考虑焊接接头疲劳损伤约束的焊接结构抗疲劳优化设计方法。
Several normal forming processes used in welded tube production were introduced, as well as its influence on the quality of welded tube.
介绍和分析了焊管生产几种常用的成形工艺,以及对焊管质量的影响情况。
There was plenty of noise inside the spheres on a recent tour, as workers welded steel, pounded bolts into place and sawed concrete inside the half-built structure.
在前不久的一次参观中,球屋里充斥着各种噪音,在这个正在建设中的建筑里,工人们在焊接钢筋,打入螺栓,切割混凝土。
As a rule, vessels shall be welded by fusion arc process.
作为规定,容器应用熔接弧焊工艺进行焊接。
Longitudinal and circumferential welded seams shall not interfere with nozzle openings, reinforcement plates and saddle pads, as far as possible.
纵向及环形焊缝应尽可能不防碍设备口、加强板、支承垫等。
Longitudinal and circumferential welded seams shall not interfere with nozzle openings, reinforcement plates and saddle pads, as far as possible.
纵向及环形焊缝应尽可能不防碍设备口、加强板、支承垫等。
应用推荐