The testing principle and the performing method of testing items such as speed, range, load, discharge voltage and current for electro-hybrid bicycle are described based on deciding the items.
分析和确定了电动助力车主要性能的检测项目，并对车速、续行里程、载荷、蓄电池的放电电压和放电电流等被测项目的检测原理及实现方法进行了探讨。
The work principle of the control circuit for inductance discharge device and the method of high effective device of finger-fork discharge are introduced.
本文通过臭氧对汽车排放的影响和电感放电的特征的分析，介绍了新型电感放电装置控制电路的工作原理和高效放电指叉的工作方法。
Reasons for corona discharge nearby the flange of transformer bushing are analyzed, and puts forward processing method.
分析了变压器套管法兰附近发生电晕放电的原因并提出处理方法。
After the derivation of the Saint-Venant Equations, water level and discharge of each cross-section are derived by the recursion method and the principle of water balance.
对圣维南方程组进行离散后，用追赶法对各河道进行演算，由水量平衡原理对各结点进行计算，就可求得河道各断面的水流情况。
Some properties of the impurity in the HL-1 tokamak are studied by the VUV spectroscopic method under different discharge conditions: regular, with wall carbonization and with a pumping limiter.
本文叙述了用真空紫外光谱方法观测HL - 1装置常规、器壁碳化和抽气孔栏三种放电条件下等离子体杂质的变化以及某些杂质的特性。
It is an effective method for improving test precision that the water head loss tests of hydropower station inlet section are performed by increasing discharge or raising reservoir water level.
同时采用加大流量法和提高库水位进行进水口段的水力损失试验，对提高试验精度是一个行之有效的方法。
The measuring method of the DC partial discharge for high voltage equipments is discussed and studied in the paper. Several measuring systems of the DC partial discharge are developed.
本文探讨了电气设备的直流局部放电测量方法，提出了几种测量系统。
The main factors affected on the drilling speed of drilling method are rock-cutting and mud discharge.
影响钻井法钻进速度的因素主要有破岩和排渣。
Since carbon nanotubes (CNTs) have been discovered in 1991, they are mainly produced by arc-discharge evaporation and Chemical vapor Deposition (CVD) method.
纳米碳管自1991年被发现以来，目前主要的制备方法有电弧法和化学气相沉积(cvd)法。
And then a method of partial discharge monitoring based on pulse current and a technique of fault diagnosis based on the minimum distance method to stator winding are presented.
接下来提出采用脉冲电流法完成定子放电故障信号的采集，应用基于最小距离法对定子局部放电样本进行故障识别。
At the same time, fuzzy hierarchical clustering and fuzzy equivalence matrix method based on fuzzy logical are designed for partial discharge pattern recognition as contrasting experiment.
与此同时，分别设计了模糊系统聚类法和模糊等价矩阵法两种模糊网络模式识别方法对局部放电信号进行识别，作为局部放电模式识别对比实验。
The rainwater design discharge, drainage flow and rainwater storage volume are analyzed and calculated, and the calculation method of rainwater storage volume is given.
阐述了凤冈县常用集流面种类及各自的特点，以及一户四口之家雨水集蓄利用的蓄水工程容积、集流面积的计算方法。
The temperature fields during ultrasonic vibration aided electrical discharge machining in gas are simulated with ANSYS method and FEM software.
用ANSYS以有限元软件对超声振动辅助气中放电加工过程的温度场进行了数值模拟。
A simple and practical calculating method is presented and 5 different pressure discharge circuits are introduced.
提出了一种简单实用的计算方法，并介绍了五种不同类型的泄压回路。
A simple and practical calculating method is presented and 5 different pressure discharge circuits are introduced.
提出了一种简单实用的计算方法，并介绍了五种不同类型的泄压回路。
应用推荐