On the basis of a number of data of thermal balance measures and rich experience, some methods for decreasing the power consumption of submerged arc electric furnaces are proposed.
本文依据大量的矿热炉热平衡测定数据和经验，就降低矿热炉电耗的问题提出了几点看法。
Edison was not the first person to have thought of using electricity for illumination: cumbersome electric arc-lighting had been employed in public Spaces and factories for a number of years.
爱迪生不是第一个想到用电照明的人；许多年来，笨重的电弧灯就在公共区域和工厂投入使用。
To take away the refining part of the steel making cycle off an electric arc furnace, which is discussed elsewhere, is an excellent start.
把炼钢周期中的精炼阶段从电弧炉中移走（这个问题将在别处加以讨论），是一个良好的开端。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
From starting-up to stabilization of the arc, the electric current and voltage usually fluctuate acutely, which makes a great impact on other circuit components.
由电孤启动到正常工作这段时间，电网线路的电流电压波动性较大，往往给电路其它各元件造成强烈的冲击。
This welding process joints work pieces by melting the electrode and the base metal with the heat from the electric arc between the electrode and the work piece.
它是一种利用焊条与工件之间电弧产生的热量熔化焊条和母材而将被焊工件连接起来的焊接方法。
Arc fault is a major cause of the electric fire, detecting on the arc fault comprehensively and effectively is the study of this article.
故障电弧是造成电气火灾的重要原因，实现全面而有效的对故障电弧的检测是本文的研究内容。
The microhardness of JCW-S-AM coatings prepared by high velocity electric arc spraying on conditions of different process parameters was tested by hardometer.
采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW - S - AM涂层，利用显微硬度计测定各种涂层的显微硬度。
Principles of pyrogenic process, wet process and other methods are more fully described. The feasibility of the technology of comprehensively treating electric arc furnace dust is discussed.
详细陈述了火法、湿法以及其它方法处理电弧炉炉尘的原理，并且简述了这些工艺的可行性。
A new technology-the electric arc spraying technology combined by powder is introduced.
介绍一种新型电弧喷涂技术粉末复合电弧喷涂技术。
Research on harmonic analysis of arc furnace electric system based on frequency domain method.
电弧炉电气系统谐波分析的频域方法研究。
When an electric arc is produced in the material, light is produced.
一种物质中产生电弧时，光就产生了。
The results of arc pressure field, fluid velocity field, and electric potentials are identical with the results in literature.
压力场、流体速度和电势的计算结果与文献计算结果相一致。
The supersonic velocity electric arc spraying technology (HVAS) has gained satisfactory solution.
电弧超音速喷涂技术(HVAS)可以有效的解决此问题。
The electric arc furnace steel-making productivity has gained rapid progress in the recent years.
近几年来，电弧炉炼钢生产率有较大的提高。
Smelting of SiMgREBa alloy with rare earth rich slag, barite and lime in electric-arc furnace is introduced in the paper.
叙述了在电弧炉中用稀土富渣、硅铁、重晶石、石灰等原料冶炼稀土硅钡镁合金的研制过程。
The cathode electric arc source is used as the source of ion infiltrating metals.
本文用阴极电弧源做离子渗金属源。
In the electric arc spray coating the oxide content was about 10%.
而且电弧喷涂涂层中具有约10%左右的氧化物含量。
The arc furnace electric system will make appearance of more harmonic current at the series resonant point and the parallel resonant and influence of series resonant is larger for the system.
当电弧炉电气系统在串联谐振点和并联谐振点附近时，均会出较大谐波电流，而串联谐振对系统的影响更大一些。
In the course of laser-arc hybrid welding, the high frequency caused by drawing arc interfered the control system which make the laser and electric arc not able to realize the hybrid welding.
激光-电弧复合焊接过程中，由于引弧产生的高频干扰了激光器的控制系统，造成了激光和电弧不能实现复合焊接。
The company has induction furnace, electric arc furnace, ladle furnace, special machines and other pipe large, medium-sized equipment.
该公司拥有感应电炉、电弧炉、精炼炉、特种制管机等多种大、中型配套设备。
The melting and reduction of scheelite acted by high temperature electric arc are very fast.
在高温电弧作用下，白钨矿粉的熔化还原速率很快。
Stable electric arc can be ensured from undercurrent to high current.
从小电流到大电流都可以保持稳定电弧。
New controlling technology make better performance of starting arc, it can choose the most comfortable electric arc by adjusting the electric arc force knob.
新的控制技术使引弧性能更好，可通过电弧力旋钮调节电弧的柔和性，选择您最舒服的电弧。
The electric arc furnace (EAF) steelmaking is the main method used to produce special steel and alloy steel.
电弧炉炼钢是用来生产特殊钢和高合金钢的主要方法。
The microstructure of UP-SMC struck by electric arc was observed by means of SEM (Scanning Electron Microscopy).
利用扫描电镜对材料被电弧击打后的微观结构进行观察。
The microstructure of UP-SMC struck by electric arc was observed by means of SEM (Scanning Electron Microscopy).
利用扫描电镜对材料被电弧击打后的微观结构进行观察。
应用推荐