The classical sarcoplasmic masses were shown in the shape of round, arc, triangular, or fusiform in 5 cases, which located in the center, peripheral, corner or lateral side of fibers.
有5例患者可见典型的类圆形、弧形、三角形或梭形肌质块，位于肌纤维中央、外周、一角或一侧，其形态与在肌纤维中所处的位置有关。
The results demonstrated that laser can increase undercut critical speed of hybrid welding, which reaches 5 times than that of arc welding with appropriate welding parameters.
结果表明，激光能够提高复合焊接的临界咬边速度，最高可达电弧焊接的5倍。
By using manual arc welding to repair the big kiln circle, the welding process of ZG310-570 super thick cast steel piece was a success, with good running effect observed for more than 5 years.
通过对大窑轮圈采用手工电弧焊的方法进行修复，成功地解决了ZG310- 570铸钢特大厚件的焊接工艺，经过5年多的运行观察，使用效果良好。
By comparing backgouging of plasma arc with carbon arc to the welded joint of 13-5 martensitic stainless steel, the backgouging of plasma arc is proved feasible for the full penetration weld.
通过对13 -5型马氏体不锈钢焊接接头进行等离子弧清根及碳弧气刨清根的比较，证明等离子弧清根对全焊透焊缝实施背面清根是可行的。
Firstly, based on analysis of arc welding robots structure characteristics, the requirements of working space and the task feature, a 5-freedom pending robot structure is proposed.
首先，分析了弧焊机器人的结构特点，并根据工作空间要求、作业特点，确定了一种5自由度悬挂式构形。
Results 15 cases presented crescent-like watery density under the skull, 8 cases presented arc-like watery density beside cerebral falx, while the remaining 5 cases presented both.
结果15例表现为颅骨内板下新月型水样密度影，8例表现为大脑镰旁弧型水样密度影，5例上述两种类型均有表现。
Argon arc welding labor 5: Has the welder card.
检验员3名。氩弧焊工5名：有焊工证。
When the cross-flow to jet Reyuolds number ratios are greater than 0. 5, the jet impingement Nusselt numbers arc obviously lower than that without cross-flow.
当横流雷诺数与射流雷诺数之比大于0．5之后，有横流时的冲击射流冷却局部努赛尔数比无横流时有较为显著下降。
Setting up a switch each one of arc welding generator, length of line can't exceed 5 meters , the length of line two times can't exceed 30 meters , the circuit is required intactly.
电焊机每台设置一个开关，一次线长度不得超过5米，二次线长度不得超过30米，线路要求完好。进出线端头应压接牢固，并安装可洗防护罩，焊机设置点应防潮、防雨、防砸和专人负责管理。
The make-break test shows that AgC 5 contact material fabricated by nano-phase coating possesses good resistance against arc erosion.
分断实验表明 ：将纳米技术应用到银 /石墨触头材料的制备中 ，使材料的抗电弧磨损性能有了较大的改善。
For a specific fire control dynamic performance test system, its measurement result was 2.34" by using the method, which improved angle precision from 20 to 5 arc-second."
利用该方法测得某型火炮动态性能测试系统的测角精度为2.34″，将该系统的测角精度从20″提高到5″以内。
For a specific fire control dynamic performance test system, its measurement result was 2.34" by using the method, which improved angle precision from 20 to 5 arc-second."
利用该方法测得某型火炮动态性能测试系统的测角精度为2.34″，将该系统的测角精度从20″提高到5″以内。
应用推荐