This process is known as full annealing because it wipes out all trace of previous structure, refines the crystalline structure, and softens the metal.
这过程被称为完全退火，因为它去除了以前组织结构的所有痕迹、细化晶粒并软化金属。
Based on the analysis of practical workpiece position calibration, an algorithm for calibrating workpiece position based on simulated annealing was carried out for robot welding.
从实用的角度分析了焊接工件的定位问题，提出了在机器人焊接条件下，基于模拟退火算法的工件位置标定算法。
It was pointed out that more strict requirements had been seen with respect to the ability to resist accumulated burl of the coatings used for the surface protection of the annealing furnace of a.
随着对汽车板表面质量的要求不断提高，对退火炉炉辊表面喷涂层抗积瘤性的要求也随之提高。
This will bring out edge crack when strip steel rolling. This problem can be solved by annealing again.
导致轧制时出现边裂，采用重新退火，进行退氮处理可解决这一问题。
An extensive study has been carried out on the effect of thermal annealing on carrier lifetime and surface recombination velocity, which affect the final output of the solar cell.
我们又进一步研究了退火对少数载流子寿命和表面复合速率的影响，因为其对太阳能电池的最终效率影响很大。
In addition, the annealing process of SiC films is mostly carried out in vacuum, argon gas or nitrogen gas ambience.
另外，对碳化硅薄膜的退火处理大多是在真空、空气、氩气或氮气气氛下进行。
Some observations of voids formation were carried out by using low carbon steel with three kinds of heat-treatment, namely, normalizing, annealing and spheroidizing.
对三种不同热处理(正火、退火、球化)的低碳钢中微空洞的形成进行了一些观测。
In this article, a thorough investigation has been conducted into heating rate, holding time and cooling speed in an effort to work out an optimum ingot annealing process.
本文对铸件退火时如何控制加热速度、保温时间、冷却速度进行了充分的研究和探讨，为合理制定铸件退火工艺指出了方向。
If the motor rotor is not carried out annealing treatment, motor's performance couldn't be influenced.
电机转子不进行退火处理，并不会影响电机的性能。
If the red hot wire directly out of the cooling, the annealing is not complete, steel wire hardness, not easy to spring.
如果把烧红的钢丝直接取出冷却，则退火不完全，钢丝硬度大，不易绕制弹簧。
The process of annealing of cold rolled coil is carried out to obtain the desired properties in the finished coils.
卷线圈的寒冷的核酸混合的加工被实行在完成的线圈中获得被需要的性质。
Finally, annealing process is carried out in the electroplated metal layer formed by the electroplating process through chemical vapor deposition method under promotion of ammonia plasma.
之后，利用氨气等离子体促进化学气相沉积法对上述经电镀制程而形成的电镀金属层进行退火处理。
The method for preparing the matt alloy aluminum foil is carried out according to the following steps: first, casting an ingot and annealing;
本发明的亚光合金铝箔制备方法按如下步骤进行：一、铸锭、退火；
The method for preparing the matt alloy aluminum foil is carried out according to the following steps: first, casting an ingot and annealing;
本发明的亚光合金铝箔制备方法按如下步骤进行：一、铸锭、退火；
应用推荐