Once I have enough turning room behind me, I roll left, pitch back right, and Angle the Raptor back toward the crowd.
一旦我的身后有了足够的空间，我就向左滚转，蹬右舵，让猛禽飞回人群上空。
You can approximate the current roll Angle by integrating the roll rate over time, but you can't do so without some error creeping in.
可以通过角速率值的时间积分来估计当前的横滚角度，前提是没有误差的累积。
The roll Angle is constrained by the control system.
滚动角度是由控制系统来限制的。
Tilt the proofer at a 45 degree angle resting the rubber roll on the substrate.
倾斜45度角搁在基板上的胶辊打样机。
In terms of the aircraft characteristics, the aircraft dynamics are divided into fast dynamics of Angle speeds and slow dynamics of roll Angle, Angle of attack and sideslip Angle.
根据飞机的动态特性，将飞机动态分为角速度快速动态与滚转角、迎角与侧滑角表示的慢动态。
Meanwhile, it also discusses the influence of roll yaw on sideslip in spin, and of moving round plumb line on Angle of bank.
同时就尾旋中偏滚对尾旋侧滑的影响、绕铅垂轴旋转对坡度的影响等进行了讨论分析。
A new roll Angle measurement system using transverse Zeeman laser is presented.
提出了一种基于横向塞曼激光器的新的滚转角测量系统。
Also analyzed are the deformation characteristics of the metal when conical roll is used and there exist both toe Angle and feed Angle.
分析了采用锥形轧辊，在辗轧角和送进角同时存在时金属的变形特点。
For the aircraft with moderate swept wing, the main reasons of causing wing rock are the variations of roll damping moment with the Angle of attack and the sideslip Angle.
对具有中等后掠角机翼的飞机，产生机翼摇晃的主要原因是滚转阻尼力矩随迎角和侧滑角的变化。
Using numerical calculation, optimal roll program, the ratio of lift and drag, reentry Angle and reentry time of spacecraft are gotten.
通过数字计算，得到飞船的最优滚转程序、升阻比、再入角和再入终端时间。
This new roll shape is very effective for improving pierced quality of low plastic steel and intensifying piercing process with larger cross angle.
这种新辊型对低塑性钢穿孔质量的改善和实现大前进角强化穿孔过程都有很大意义。
Knee roll: As the weight shifts onto the new ski the knees roll into the Angle of the new turn.
膝盖转动：随着重心移到新的雪板上，膝盖转动到下个回转的角度。
Roll pass on Angle steel rolling, I-beam rolling and U-section, etc. were intensively studied.
他对角钢孔型轧制的，工字钢轧制和U -型钢轧制等剧做过深入研究。
This paper gives the method that is effective in decreasing the roll Angle and roll rate in roll channel of the reentry vehicle.
针对再入飞行器滚动通道产生较大的滚动角及滚动角速率，给出了一种能够有效地减小滚动角和滚动角速率的方法。
This is to be completed in the time it takes the body to roll to, decelerate, and stop at the maximum rotation Angle and then to accelerate and roll in the opposite direction.
这个动作在身体滚动的同时完成，减速，并在最大转动角度停止然后加速并转动到另一边。
The effects on straightness measurement are analyzed for the cube-corner retroreflector with angle errors, surface errors, yaw, pitch and roll.
分析了角锥棱镜的制造角差、面形误差和测量过程中角锥棱镜的偏摆、俯仰、滚转对直线度测量的影响。
The paper set up mechanics model of roll cylinder mill, inquired into crushing stress of materials by mill and materials clamp Angle and energy requirement problems.
本文建立了辊筒磨的力学模型，探讨了辊筒磨对物料的粉碎力、以及物料钳角、单位质量能耗等问题，并通过实验进行了验。
The methods are devoted to determining aerodynamic performances for asymmetrical body with Angle of attack, Angle of side slip and roll Angle.
可用来计算有攻角、侧滑角、滚转角的非对称体的气动特性。
The experimental curves of moment and angle are got by platform roll test.
通过台架横摇试验，绘制了力矩和角度试验曲线。
The principle of roll angle determination for projectile based on geomagnetism detection was introduced, the static and dynamic experiments for roll angle determinatio.
介绍了基于地磁探测的弹丸滚转角辨识原理，进行了滚转角辨识系统静态与动态试验。
A zero-install roll Angle of the wrap around fins projectile still has roll moment at zero Angle of attack.
卷弧翼与弹身扣合较好，在零攻角下会产生滚转力矩。
The paper analyzed the correlation of pitch angle and roll angle, which were measured by magnetic head flying angle adjustment apparatus, and introduced a method of angle adjusting.
分析了磁头飞行角度调校仪器不同工位测量磁头俯仰角和翻转角之间的相关性，并简单介绍了角度调校方法。
Down coiler is one of the key equipment for hot strip mill, the deviation angle of tension roll is of great importance to biting into coiler successfully.
地下卷取机是热带钢连轧机的关键设备，张力辊的偏移角对于保证带钢顺利咬入具有重要的作用。
The difference is that to make water to roll-off a Teflon coated material, you need to tilt the surface to nearly a 70-degree Angle before the water begins to slide off.
不同点在于，要使水滴从特氟龙涂层表面滚落，需要在水滴滚落之前将这个表面倾斜到70度。
These factors include ratio of upper and lower roll diameter , reduction ratio , enterance angle and roll rotation speed.
因素有上下轧辊直径比、压下率、导入角和轧辊转速。
Result showed that main reasons on ablation of roll bearing were transformation of forward Angle, flow value of cool water, water pressure, water pipe position, and deformation of roll-shell et al.
对造成轧辊烧轴承的原因进行了分析，结果表明：轧辊烧轴承主要与轧辊送进角的变化，冷却水的水量、水压及水管位置，轧辊架变形情况等有关。
The feasibility of reducing roll angle and improving comfort of commercial vehicles by using this type of stabilizer is studied in the paper.
本文研究了该稳定器对降低车身侧倾和提高舒适性的效果。
In this paper, the locating method of pneumatic boring machine is analyzed and an important sensor is designed, which can measure the roll Angle of pneumatic boring machine.
对冲击式曲线穿孔机的空间坐标定位方法进行了有效的分析，并对一个重要的定位元件———旋转角度传感器进行了研究。
Fin stabilizer is one of the most important effective ship roll reducing equipments, which has many defects in the classical Angle feedback system.
减摇鳍是一种非常重要的船舶减摇装置，但传统的鳍角反馈减摇鳍在设计中存在着很多问题。
Fin stabilizer is one of the most important effective ship roll reducing equipments, which has many defects in the classical Angle feedback system.
减摇鳍是一种非常重要的船舶减摇装置，但传统的鳍角反馈减摇鳍在设计中存在着很多问题。
应用推荐