The press was looking for a new Angle on the story.
新闻界正在为这件事寻找一个新的角度。
Press A / M, out of the valve angle calibration, ether the no input signal valve position calibration process.
按下A/M，退出阀门转角标定，进入无信号输入阀门位置标定进程；
In addition, the conception of press Angle of spatial CAM mechanism is discussed and its mathematics model and self-adaptive arithmetic are given also.
另外，利用等距曲面的概念讨论了空间凸轮机构压力角的概念及其自适应求解模型。
When dig high cutting, except the control of side slope Angle and shoulder (road) 's elevation, width. We also should control roadbed's filling and press degree.
路堑开挖除对边坡坡率以及路肩标高、宽度进行控制外，还要对基床填料及压实度进行严格控制。
This is a dissertation on observing the Press Conference through a visual Angle of communication.
这是一篇从宣传学的视角观察新闻发布会的论文。
Therefore makes the room not to be possible the general's family to make to this angle, the important daily life behavior cannot press in clever on-line.
因此造屋绝不可将门造于此角，重要的起居行为不可压在鬼线上。
The author resumes the integrated feature of commercial web printing press from the Angle of technology.
作者主要从技术的角度对商业轮转印刷机的特征做了一个全面的概述。
During different lift range phases when a CAM controls the distribution spool of a giant hydraulic press, the CAM's requirement for the pressure Angle of its theoretical working profile is different.
凸轮机构控制巨型液压机分配阀芯时，在不同的升程阶段对凸轮理论工作曲线压力角有不同的要求。
According to defining of the global CAM curve, the resolution express of press Angle about a new type of indexing mechanism with arc surface CAM is provided.
根据空间凸轮曲面压力角的定义推导出新型弧面凸轮分度机构压力角的解析表达式，分析该机构压力角出现最大值的情况，同时对如何降低最大压力角提出了一些改进措施。
Key control Guo Jing around to the corresponding reorientation Angle of the shot, press the space bar can archery.
方向键左右可以控制郭靖向对应的方向调整射击角度，按下空格键即可射箭。
In order to adjust the bending Angle, the t type slide seat and bending press plate were used. The adjusting of bending radius was implemented by replacing the adjusting axis of bending radius.
模具采用T形滑座与弯曲角两边的压板调节，从而达到在一定范围内调节弯曲角度的目的，弯曲半径的调节主要是通过更换弯曲半径的调节轴来实现。
At the same press bending Angle, the cross section distortion of the tubes decreases by increasing the distance between the die fulcrums.
在相同的压弯弯曲角度下，增大凹模支点的间距可以减小管坯截面的畸变。
Adjust an Angle and speed of the rocket and press the red button.
调整火箭的角度和速度，并按下红色按钮。
In order to adjust the bending Angle, the T-type slide seat and bending press plate were used.
模具采用T形滑座与弯曲角两边的压板调节，从而达到在一定范围内调节弯曲角度的目的。
In order to adjust the bending Angle, the T-type slide seat and bending press plate were used.
模具采用T形滑座与弯曲角两边的压板调节，从而达到在一定范围内调节弯曲角度的目的。
应用推荐