This testing machine is good at studying the deformation and failure of inhomogeneous and discontinuous media from the Angle of loading equability.
该试验装置可以更好地从均匀加载的角度研究非均匀，非连续介质的变形及破坏规律。
With the increase of cutting depth, under the impact of abrasive particles with a large Angle, an oblique stripe deformation of the grinding zone are formed.
随切深的增加，材料在磨料粒子大角度冲击下形成斜条纹状的变形磨削区。
Study showed that angle deformation of T joint is changed along the welded seam length.
研究表明，T形接头的角变形沿焊缝长度方向是变化的。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。
The analysis of free vibration of hydropower house by means of two methods are deformation of inclination Angle and slope deflection.
本文首先叙述用两种方法(倾角变位法和角变位移法)分析水电站厂房的自振特性。
Relationship curves between seam dip Angle, horizontal section height and roof deformation are derived, at the seam time, the criterion of failure is given in this paper.
得出了煤层倾角、水平分段高度对顶板变形的影响关系曲线，同时，给出了顶板破断的判据。
Linear deformation zone of generating wall can be obtained by means of non-linear cone Angle plug combined with the barrel-shaped rolls, so the wall accuracy can be increased greatly.
采用带有非线性顶头锥角的顶头与桶形辊相配合可以获得线性的成壁变形区，从而大大提高壁厚精度。
The coupling among laser modes and the relations between equivalent beam spread Angle and the surface deformation of the mirrors are obtained.
给出了激光模式之间的耦合以及等效光束发散角与镜面变形量之间的关系。
Using the theory of stochastic dielectric, the laws of deformation in space of different Angle in coal layers have been deduced.
利用随机介质理论，建立了不同倾角煤层的采空区所对应的地表空间变形规律。
When the traction Angle was constant, the displacement and stress of the cervical column as well as the deformation of intervertebral space were all increased with the enhancing of traction force.
当牵引角度不变时，随牵引力的增大，颈椎的位移及各点的应力均增大，椎间隙的形变亦更明显。
The stress, deformation and force of top bearing bracket and stator frame with sk ew leaf springs are analyzed, and optimum angle of skew leaf springs is given in this paper.
对采用斜形连接板的上机架、机座的应力、变形和受力进行了分析，给出了斜形板的最优安放角度。
This paper analyzes the influence on the pivot point and deflection angle from the pendulum shaft's deformation in course of the test.
本文分析了试验过程中摆杆形变对柔性接头摆心、摆角数据的影响。
Result showed that main reasons on ablation of roll bearing were transformation of forward Angle, flow value of cool water, water pressure, water pipe position, and deformation of roll-shell et al.
对造成轧辊烧轴承的原因进行了分析，结果表明：轧辊烧轴承主要与轧辊送进角的变化，冷却水的水量、水压及水管位置，轧辊架变形情况等有关。
The paper puts forward the concept of normal Angle of winding bend for describing the degree of distortion and deformation of malformed winding bend.
为了描述畸形河湾扭曲变形的程度，提出了河湾法向角的概念。
Through the mechanical analysis, the differential equation for the longitudinal deformation of cold forming steel is derived, and the formula for longitudinal rotation Angle is obtained.
对冷弯型钢的纵向变形过程进行了力学分析，得到了变形微分方程，求得了转动角的理论公式，并对其变形形状进行了分析计。
To general problem of the slab head bending in rolling, the effect of geometric shape coefficient of the deformation zone and entry Angle on head bending is researched.
本文针对中厚板轧制过程中因头部翘曲而影响产品质量和产量这一生产中普遍存在的问题，研究了变形区几何形状系数和送入角变化对轧件头部翘曲的影响。
The relation between load and deformation of the spring element is analysed and the calculating methods of constant angle and maximum axial load are set up.
本文研究了自动调心分离轴承装置的结构和调心原理，分析了弹性元件载荷与变形的关系，给出了分离轴承接触角和极限轴向负荷的确定方法。
By analyzing and studying the survey data, we have obtained ground movement and deformation rules and different kinds of Angle parameters as well as prediction parameters under the condition of.
通过对观测资料的分析研究，获得了该区条件下高强度综放工作面开采时的地表移动变形规律、各种角值参数和预计参数。
By the theory of elastoplastic bend, this paper prowents a method to calculate out - of -- plane restraint and reverse deformation that are made use of to remove angle deformation in butt joints.
本文应用弹塑性弯曲理论提出了一种消除焊接对接接头角变形的平面外拘束力的计算方法，计算了极限拘束力、拘束长度和反变形的量值，并通过试验验证了方法的有效性。
By the deflection test, the deflection produced by the deformation of joint field can be gained, accordingly, the change in the included Angle that the beam axis relative tot...
通过挠度测试，可以求出因节点域变形导致梁发生转动而产生的挠度值，进而可以得到梁柱夹角发生的改变量。
The dip Angle is a main factor to decide the image shape of crustal deformation field.
力的方位角是决定形变场图像形态的重要因素。
Also analyzed are the deformation characteristics of the metal when conical roll is used and there exist both toe Angle and feed Angle.
分析了采用锥形轧辊，在辗轧角和送进角同时存在时金属的变形特点。
Shearing Angle can be adjusted within a certain range, which can reduce the shearing deformation of sheet metal and can shear much thicker sheet metal.
刀架剪切角能在一定的范围内调整，可使剪切材料变形量减小到理想状态，又可剪切超厚板料。
The conception of deformation angle of helix pre-former is introduced and process parameters are analyzed with math regression method.
以T形焊接接头为算例，结合热弹塑性有限元法和映射应变分量法，研究了角焊缝角变形的产生机制。
The micro angle induced by the tooth surface elastic deformation causes the change of meshing points. Quasi-Hertzian analysis is defined as the process of tooth meshing analysis.
将齿轮因齿面变形而产生微小转角，继而进行齿面啮合分析的过程定义为拟赫兹接触分析。
Bigger inclination Angle of shear band leads to bigger dissipated energy of lateral plastic deformation and smaller dissipated energy of lateral plastic deformation.
增加剪切带倾角，侧向塑性变形消耗的能量占剪切带消耗的能量的比例增加。
The effects of various amounts of deformation, steel grades, degrees of hardenability, die entry angle and drawing speeds on dia. sinking drawing are studied.
研究了不同变形量、钢种、硬化程度、模角和拔制速度对空拔管直径缩小量的影响。
The effects of different structural parameters, such as contact Angle, deformation and stiffness and load parameters on bearing mechanical properties were studied.
研究了不同结构参数和载荷参数对滚珠轴承力学特性的影响，得到了滚珠轴承接触角、变形以及接触刚度的变化规律。
To counter the motion deformation characteristicscs of accumulation landslide. the monitored data of landslide displacement with grey theory and acqifcs displacement vector angle were dis-cussed.
针对堆积层滑坡变形破坏特点，运用灰色理论，对滑坡位移观测资料进行了处理，求出了灰色位移矢量角。
Equations of end Angle deformation of legs are established based on elastic stability theory, where from stability equation is deduced.
根据弹性稳定理论，建立腿端转角方程，并由此导出稳定方程。
应用推荐