Changing the Angle at which the extrudate is drawn away from the die can change the placement of buildup on the die and make it easier to clean.
改变挤出物的牵引角度，就可以改变挤出物在口模上的堆积位置，这样就容易清除积料了。
Based on the investigation of die Angle, pressing route and pressing temperature, the optimum parameters were chosen in the experiments of equal channel angular pressing (ECAP).
在对等通道角挤压中模具通道夹角、挤压路线和挤压温度研究的基础上，确定了实验中的理想工艺。
The theoretically calculating results are compared with those of experiment and the optimum die Angle in nosing process is proposed.
对刚塑性有限元计算的结果与试验结果进行比较，并提出缩口的最佳模角。
The tensile strength, zinc coat mass and service life of die of galvanized steel wire after drawing are compared on the condition of different work cone angle.
在不同的工作锥角度下，比较镀锌钢丝拉拔后的抗拉强度、锌层质量、模子寿命。
Under normal production conditions, the die angle, friction coefficient, tube material and material temper can be neglected in the calculation.
双周数表通用性较强，在一般的生产条件下，可以不考虑模角、摩擦系数、管材材质及其状态等因素；
In addition, this paper presents how the diameter reducing rate, the die semicone angle, the friction coefficient and the original wall thickness influence the buckling and the axial elongation rate.
并分析了缩径率、缩径凹模半锥角、摩擦系数、缩径管坯初始壁厚对管端翘曲和轴向伸长率的影响规律。
A new type of practical mould structure with tightwire and idler wheel for Angle core pulling of die injecting a Angle bracket is presented.
针对把手注射模的新设计，阐述了把手注射模的结构形式，并重点分析了模具斜顶抽芯机构的设计。
How to optimize the design of Angle bar die and the concrete process of die design are introduced.
介绍如何优化设计角板冲模模具，以及模具设计的具体步骤。
The thesis presents a practical die structure with Angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构，论述了模具结构特点和工作过程。
The results show that under different types of compensation Angle, pallets power and die gap, the bending springback rules of the tailored blanks are in line with the light board.
结果表明，在不同补偿角、托板力和模具间隙的影响下，激光拼焊板具有与光板一致的回弹规律。
The thesis presents a practical die structure with dog-leg CAM and Angle pin for secondary combined Angle core pulling of die casting draw hooks.
本文给出了拉钩铸件弯销-斜销二级联合斜向抽芯压铸模实用结构，论述了模具分型面的确定、结构特点和工作原理。
There is a shedder on the upper die of the new type of finish forging die so that pattern draft Angle of half axle of forging is small oversize for machining is little.
新型精压模的上模设有顶件装置锻件半轴的拔模斜度小锻件半轴的金属敷料少。
The experimental results demonstrate that the main factors affecting texture formation are die Angle and the friction between the wire and die.
拉拔角、钢丝帘线与拉拔模具间的摩擦力是影响织构形成的主要因素。
By numerical simulation of a six-tooth rectangle spline, the optimized half-angle of the concave die can be got.
结合六齿矩形花键轴实际成形情况进行模拟计算，获得了入模半锥角的较佳取值范围。
But the method of cutting an obstacle angle in the die is not widely applied due to its operation problems and unclear mechanism of resistance increasing.
开障碍角的办法由于其自身的可操作性问题和增加阻力机理不明确，并没有广泛地应用。
The shape of each die forms a circular table shape, and each die has a definite cone angle.
所述的模具外形呈圆台状，具有一定的锥角；
The effects of various amounts of deformation, steel grades, degrees of hardenability, die entry angle and drawing speeds on dia. sinking drawing are studied.
研究了不同变形量、钢种、硬化程度、模角和拔制速度对空拔管直径缩小量的影响。
The springback Angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases...
回弹角随凸模圆角半径和凸凹模间隙的增大而增大，随压边力、板料厚度、摩擦系数和材料硬化指数的增大而减小。
At the same press bending Angle, the cross section distortion of the tubes decreases by increasing the distance between the die fulcrums.
在相同的压弯弯曲角度下，增大凹模支点的间距可以减小管坯截面的畸变。
The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.
本文给出了拉钩铸件弯销-斜销二级联合斜向抽芯压铸模实用结构，论述了模具分型面的确定、结构特点和工作原理。
There is a shedder on the upper die of the new type of finish forging die, so that pattern draft Angle of half axle of forging is small, oversize for machining is little.
新型精压模的上模设有顶件装置，锻件半轴的拔模斜度小，锻件半轴的金属敷料少。
A lower die Angle means a better hardness.
模具转角越小，显微硬度越高。
The boron-doping technology and metallurgical micro-structure of die steel are discussed from the angle of its resistance to repeated shock compression.
结果指出：模具钢渗硼层在多次冲击压缩载荷下发生一定的塑性变形。
The crack appears at the edge angle due to stress concentration caused by alternating load, which finally leads to the fissuring of die plate.
凹模在使用过程中，由于交变载荷的作用，使碳化物的棱角处应力集中出现裂纹，最终导致凹模开裂。
The experiment shows that the magnitude of dia. sinking is increased with the increase of reduction and die entry angle;
实验表明，直径缩小量随减径量和模角的增大而增大；
As applications, two examples, which concern pouring temperature of nonferrous alloys and minimum ejecting angle recommended for die cavity, were given. The results showed that …
研究了有色金属压铸成型工艺模糊智能化设计中浇注温度和出模斜度的问题。
The thesis presents a practical die structure with dog-leg cam and angle pin for secondary combined angle core pulling of die casting draw hooks.
本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构，论述了模具结构特点和工作过程。
Take the international lead of die cutting process, to ensure the best vertical Angle of the flooring.
领先于世界的冲切工艺、确保了地板直角达到最佳，整体感好，可用于打造各种风格的连锁店地板。
Dissertation was made on the structure characteristics and principle of the die-casting die with dog-leg CAM and angle-lift splits core-pulling mechanism.
给出了实用的弯销与斜滑块抽芯结构，论述了其结构特点和工作原理。
The working principle of the die casting mould has been discussed, and the core pulling force, the core pulling distance and the diameter of the angle pin have been confirmed by calculation.
论述了壳体铸件压铸模工作原理，通过计算确定了抽芯力和抽芯距离以及斜销直径。
应用推荐