I then set that layer to Overlay and 50% Opacity, then duplicated it and set the duplicate to Soft Light and 50%.
然后我将这个图层的模式设置为叠加，50%透明，再将它复制一层，将复制的图层模式设置为柔光，50%透明。
Then set the bowl in a basin of cold water and beat for a minute or two until the mixture is light, fluffy, and a pale ivory color.
用木勺搅打数秒，直至黄油变软。然后再把碗拿出来放在一盆冷水中，再搅打一到两分钟直至黄油糊变得很轻，蓬松，有点发白就可以了。
When the input voltage is higher than the overvoltage set point of the machine, the machine immediately shut down, and then red light flashes.
当输入电压高于机器过压点的设置，机器立即关闭，然后红灯闪烁。
Another trick I like to use often, is to add another layer on top of everything and paint the general colors I want in each part of the image, then set it to soft-light and lower it's opacity.
另一个我常使用的窍门是给在最顶层添加一层，并在我希望的位置进行绘制，然后设置它的叠加方式为柔光，并降低它的透明度。
Note that by default the light will go out in 1 second, if longer timeout is needed, then you can set it with settings options between 1 sec and 3599 (1 hour) seconds.
请注意，默认情况下，光线会在1秒钟，如果需要更长的超时，那么你可以设置从1秒和设置选项时，它3599（1小时）秒。
When the blazing sun is set, And the grass with DEW is wet, Then you show your little light, Twinkle, twinkle, all the night.
当炽热的太阳降落时，芳草为露水沾湿时，你就显示你的微光，闪耀眨眼通宵达旦。
Then he would lock his own little office and set the proper light burning near the safe, after which he would take his departure.
然后，他锁上自己的小办公室，开亮保险柜旁的专用灯，这才离开。
I set my camera to expose for ambient light, and then used flash which I dialed down.
我设置相机使环境光曝光正确，接着使用闪灯并调低曝光补偿进行补光。
We will then set it to Soft Light, and then lower the opacity to about 62%.
我们然后将其设置为柔光，然后降低至约62%的不透明度。
Then I take a large, blurred edge brush on eraser setting, set to perha 50%, and take out areas on this darkened level that I want to a ear as light.
下面，我在擦除设置中选一个大的，边缘模糊的刷子，设置到50%，去处掉在这个暗化的图层中我期望表现为亮的区域。
And then I said farewell to sun light, and set out to become what I became.
然后我就对阳光永别了，变成了我现在的这个样子。
I then set that layer to Overlay and 50% Opacity, then duplicated it and set the duplicate to Soft Light and 50%.
我们将这个图层的模式设置为柔光，50%的不透明度。最后我们得到了一个很好的光照效果。
I then set that layer to Overlay and 50% Opacity, then duplicated it and set the duplicate to Soft Light and 50%.
我们将这个图层的模式设置为柔光，50%的不透明度。最后我们得到了一个很好的光照效果。
应用推荐