Amplifier class has absolutely nothing to do with output stage topology.
放大器级绝对没有任何关系与输出级拓扑。
This thin-style high-power amplifier with versatile charm featured the definitive high-efficiency class A amplifier, the HCA circuit.
这款是全能高效率的A类放大，薄型高功率功放。
This paper introduces the fundamental principles and character of PDM modulation of class E amplifier square circuit.
本文介绍了E类放大器方阵电路PDM调制的基本原理和调制特性。
In order to get the highest working efficiency of Class-E amplifier, it needs to get the exact values of shunt capacitance.
为了使E类放大器工作效率最大，需要得到并联电容的确切数值。
Driver deadtime control is a popular scheme used to prevent the occurrence of the shoot-through issue in a Class-D APA (audio power amplifier).
在D类音频功率放大器中，驱动死区时间控制是一个很流行的术语。
A current-driven common source amplifier which is biased on class AB constitute the output stage.
由偏置在AB类的电流驱动的共源放大器构成输出级；
The new algorithm is applied to the simulation of a class C amplifier, current waveforms at drain and source show good agreement with those obtained by MEDICI transient analysis.
采用该算法仿真典型的C类功率放大器得到电流波形和工业界公认标准器件仿真器MEDICI瞬态模拟得到电流波形比较，显示出很好的一致性。
Class E amplifier is a new kind of high-efficiency power amplifier.
类功率放大器是一种新型高效率放大器。
Therefore, class F amplifier has caused widespread concern at home and abroad, and also has good prospects for the study.
所以F类放大器在国内外已经引起了广泛的关注，并拥有很好的研究前景。
In order to improve both charge current and transfer efficiency via a lower coupling coefficient inductive link, class E power amplifier based on primary leakage inductance and compensat.
在低耦合系数条件下 ，通过基于初级漏感的E类功率放大器和次级漏感的补偿方法 ，提高电容充电电流和传输效率。
As one side reaches saturation, the other side reaches cutoff, just as they would in a single-ended class a amplifier.
作为一方达到饱和，另一方达到临界，就像他们将在一个单端A类放大器。
By using the scheme, the Class-D amplifier has gained high efficiency and high performance, and it can lower the requirement of output filters.
利用这种方法实现的D类功率放大器具有高效率高性能的特点，并能降低滤波器性能的要求。
This thesis does research on the key module of Q-switch driver—high efficiency Class-E power amplifier, including the design and implement of the prototype.
本文主要研究了声光Q开关驱动器的关键模块——高效率E类功率放大器，设计实现了工程样机。
It is simply the same class amplifier it was to begin with, but driven into clipping.
这只不过是同一类放大器，这是开始，但驶入剪报。
什么是B类放大器？
Now, you might be thinking, how can a push-pull amplifier be class A?
现在，你可能会想，怎么能推挽放大器是A类？
Technically speaking, you can have a a class AB single-ended amplifier, which was biased away from the linear portion of the curves, but that amplifier would hopefully!
从技术上讲，你可以机管局A B类单端放大器，这是有偏见的距离线性部分的曲线，但放大器将希望！
The class E power amplifier hasn't widely used because of a variety of problems, one of which is the difficulty of adjustment.
高效率E类放大器的提出是功率电子学研究方向的重大突破，但它由于受到各种因素的限制，还未能得到广泛应用。
The controller combines parallel amplification and drain modulation of the CMOS class-E power amplifier to provide high efficiency over a broad range of output powers.
结合射频E类功率放大器的结构特点，采用CMOS工艺，达到了在大的输出功率范围内保持持续稳定高效率的目的。
With the continuous advancement of technology, design, D-type power amplifier performance is also moving into the Class AB amplifier.
随着设计技术的不断进步，D类功率放大器的性能指标也逐渐接近AB类放大器。
An improved scheme of full bridge PWM for Class-D audio power amplifier is described in the paper, and it is implemented in analog and digital way.
论述了音频D类功率放大器的全桥pwm改进方案，并用模拟与数字的方法实现。
The traditional class D amplifier is composed of three parts: modulation circuit, driving circuit and power amplification circuit.
传统的D类放大器一般由三部分组成，即调制电路、驱动电路和功率输出电路。
The true class a amplifier will have no crossover distortion, while the class AB amplifier will.
真正的A级放大器，也没有交越失真，而AB类放大器将。
Integrated circuit of a class-D audio power amplifier with very high efficiency using CMOS technology is presented in this paper.
分析了高频开关电源的特点及将其应用到音频功率放大器中所遇到的主要问题，以及解决这些问题的基本方法。
Based on the conventional Class-E resonant high-frequency power amplifier, a new control scheme used in Active-clamped Class-E inverter for ultra-high frequency induction heating is proposed.
以传统的E类高频功率放大电路为基础，提出了应用于高频感应加热电源的有源箝位E类逆变电源的一种新型控制方法。
In order to analyze the nonlinear characteristic presented in the subharmonic load pull experiment theoretically, a class a MESFET power amplifier is researched on in this paper.
为了从理论上解释副谐波负载牵引实验中的各种非线性现象，对一个A类MESFET功放进行了研究。
As long as the manufacturer isn't rating the amplifier for its output power in this clipped state, the amplifier would normally be called class a, single-ended.
只要制造商不是评价的放大器，其输出功率在此截断的国家，放大器通常被称为A级，单端。
Ten years ago, I planned to build a class A power amplifier, but I shelved it due to my limit in knowledge and ability then.
早在十几年前，我就计划做一台单端A类的放大器，但这个计划一直没有实现，直接的原因就是技术不充分。
Also, the efficiency will be greater than is theoretically possible with a class a amplifier at these levels.
此外，效率将大于理论上是可能的A类放大器在这些级别。
The total capacity of gain reaches 25dB. This thesis also described the collector modulation of the Class-E amplifier and the circuit for protection.
文中也阐述了驱动E类功放的集电极调制电路和功放保护电路的原理和设计。
应用推荐