Proper insulation must be taken after welding.
焊后采用适当的保温处理。
Inspecting welding seam of hatch coaming after welding.
货舱口围板焊接后焊缝检查。
Checking structure integrity of superstructure (deckhouse) after welding.
上层建筑焊后结构完整性检查。
Checking structure integrity of superstructure (deckhouse) after welding.
上层建筑焊后结构无缺性检查。
Brightness and excellent electric conductivity welding spot after welding.
焊后焊点光亮，导电性能优良。
The long neck flange should have stress-relief heat treatment after welding.
拼接法兰应进行焊后消除应力热处理。
No substrate deformation and collapse, no strength reduction and cracks after welding.
无基材结构变形的影响，无变形及塌陷，焊接后强度减小和龟裂。
Evolvement of longitudinal stress and residual stress field after welding are obtained.
得到了焊接过程中纵向应力的演变规律与焊后应力场的分布情况。
The repair welding technology and inspecting method after welding are mainly discussed.
重点讨论了补焊工艺及焊后检查方法。
Services: to undertake OEM orders, plug - in, after welding, assembly and testing process.
服务范围：承接OEM订单、插件、后焊、组装及测试加工。
Evolvement process of longitudinal stress and residual stress field after welding are obtained.
得到了焊接过程中纵向应力的演变规律与焊后应力场的分布情况。
Thermal cycling is an important factor to determine structure and property of HAZ after welding.
热影响区的热循环是决定焊后热影响区组织和性能的重要因素。
The power end :The frame is welded steel-plate construction. It is stress-relieved after welding.
动力端：壳体为钢板焊接结构，焊后消除内应力。
No bubble and trachoma produced, directly grinding, polishing and wrinkle treatment after welding.
无气孔和沙眼，焊接后可直接进行削磨，抛光加工及皮皱处理。
Please give the standards of the preheat before welding and those of the heat-treatment after welding.
请您提供焊前预热和焊后预热处理的规范。
Application of stainless steel after welding (not by steel) flat shovel thoroughly clean slag and spatter.
焊后应用不锈钢(不得采用碳钢)扁铲彻底清理熔渣和飞溅。
The homemade wear-resistant cast steel has high hardness and high tendency of hardenability after welding.
自制抗磨铸钢硬度高、焊后淬硬倾向严重。
Because of this, this kind of steel after welding manipulator welding, its heat treatment to avoid this temperature range.
正是因为如此，这类钢材在经过焊接机械手焊接之后，它的热处理要避开这一温度范围。
This part is made by welding and correct the defromation after welding. Unspecified weld leg is----. Grind to free of burr.
本件全部焊接，焊后整形。未注明的焊脚高度为，修光去毛刺。
The process of vibratory stress relief(VSR) is discussed to reduce the residual stresses after welding of stainless steel plate.
为了消除超大不锈钢焊接底板的残余应力，研究了采用振动时效（V SR）的方法消除焊接残余应力。
The overall annealing can effectively reduce residual stress after welding, but in the cooling, very important to control of the cooling.
整体退火能有效地降低焊后残余拉应力，但在冷却时，对降温的控制非常重要。
The effect of different welding techniques, and alignment after welding, on the residual stress of rectangular girder weldment was studied.
介绍不同焊接工艺对厢形梁焊接残余应力的影响及校直前后其残余应力的变化。
The effects of high temperature pre-precipitation on the stress corrosion properties of the heat affected zone were also studied after welding.
并研究了高温析出对焊接热影响区及后处理应力腐蚀性能的影响。
The result shows that it is more reasonable, safe and reliable to adopt procedure with warm up before welding and post heat treatment after welding.
结果表明：采用焊前预热和焊后热处理的焊接工艺方案所获得的焊接接头比不采用以上措施获得的焊接接头更为合理，应用更安全、可靠。
By simulating welding and simulating heat treatment after welding, CCT Curves of UIC900A and U75V rail steels are determined by the expansion method.
模拟钢轨焊接及焊后热处理工况，采用热膨胀方法分别测定uic 900a及u75 V钢轨钢的连续冷转变曲线(CCT曲线)。
Introduce the PCB board layout, the principle of the layout of components, debug the hardware circuit after welding and present the module debugging method.
介绍了PC B板布线、元件布局的原则，焊接后进行硬件电路调试，介绍了各模块的调试方法。
Thus three welding crafts can be used in the fabrication of offshore jacket structure directly and the offshore jackets need no heat treatment after welding.
所评定的三项焊接工艺可以直接用于海洋平台导管架建造，焊后允许不进行热处理。
Controlling for the variables related, preventing the crriage from cracking during welding and correcting distortion for it after welding are discussed, too.
提出了焊接过程中产生裂纹的控制方法及对焊后变形的矫正方法。
The stator lead wire of QD115 starter and the lug can be welded without flux filled, which avoids the phenomenon of strands of thin wires getting hard after welding.
解决了QD 115定子引出线与接线片和电器产品电源线与接线片不加填充焊料的焊接问题，避免了多股细铜线焊后变硬的现象。
The stator lead wire of QD115 starter and the lug can be welded without flux filled, which avoids the phenomenon of strands of thin wires getting hard after welding.
解决了QD 115定子引出线与接线片和电器产品电源线与接线片不加填充焊料的焊接问题，避免了多股细铜线焊后变硬的现象。
应用推荐