Correction method for parameter adjustment of machine tool under the prefixed condition of film thickness is proposed.
提出给定油膜厚度条件下，机床调整参数修正方法。
We have planned to finish the adjustment of the machine before Tuesday.
我们计划在星期二以前完成机器的调试工作。
Install the combination of car, general machine installed in the factory, shipped to the use of units, a size adjustment can be placed in the tray.
小车的安装组合，一般在制造厂就整机安装好，发运到使用单位后，稍径调整即可安放在桥架上。
This paper analyses the working parameter adjustment principles of abroad and at home hydraulic impact machine, and shows their defects.
分析了国内外液压冲击机械工作参数调节原理，并指出其主要缺陷。
Furthermore, GRP wined system can not adjustment continuously and therefore affect the technics of production due to the limitation of machine timing.
而且，由于机械调速的限制，导致缠绕系统的速比不能连续可调，影响了产品的工艺。
Good adjustable and wide applicability. The change of thickness of material layer, moving speed in the machine and full amplitude can adopt infinitely adjustment.
可调性好，适应面宽，料层厚度和在机内移动速度以及全振幅变更均可实现无级调节。
Electric adjustment phase and slotting phase of whole machine printing roller.
整机印刷版辊的周相、开槽相位电动调整。
This paper analyzes the common breakdown of submerged arc welding machine and parameters' adjustment.
继续分析了自动埋弧焊机的常见故障和相关参数调整。
In this paper, the adjustment parameters of universal rolling disk in gear grinding machine, such as generating length, eccentric distance of generating and differential crank disk are calculated.
对磨齿机中常用的展成机构——万能滚圆盘的工作台展成长度、展成和差动曲柄盘的偏心量调整的计算过程进行了推导分析。
The formulas of error by machine adjustment framework canceled is fetched.
推导出机床调整机构可消除误差的公式。
By smooth throughput estimation and rate adjustment, and the appropriated specification of the state machine of the highest layer, SLVM greatly improves the stability of video quality.
通过设计平滑速率估计、平滑速率调节机制以及接收者最高层的状态机，有效提高视频传输的稳定性。
The overflow valve is used to protect the machine and the safety of the operating personnel, must not be arbitrary adjustment.
溢流阀是用来保护机器和操作人员的安全的，不得任意调整。
NSK-I type of controller of the tightening up a screw machine is a new type of the torque controller. It has achieved continuous adjustment to the torque of the controlled motor.
型拧丝机控制器作为一种新型的力矩控制器，实现了对被控电动机力矩的连续调节。
There was difficulty in charge of the original machine structure, the long adjustment time, the heavy physical labour and so on.
机床原有结构存在入料困难，调整时间长，劳动强度大等。
The Construction principle, mechanical properties, basic shock parameters and adjustment methods of cam-type drop -test shock machine are described.
阐述了凸轮式跌落冲击台的结构原理、力学性质、冲击参数与其调整方法。
The writer discusses the machine of new product on improvement and adjustment, and emphasises the important of equipment basis.
就新产品的上机织造从设备改进与调整等方面进行了综合论述，并强调了基础设备的重要性。
The construction principle, mechanical properties, basic shock parameters and adjustment methods of cam-type drop-test shock machine are described.
阐述了凸轮式多次跌落冲击台的结构原理、力学性质、冲击参数及其调整方法。
The article discussed the installation and adjustment of NC sand belt grinding machine and to raise a proposal where need to pay attention.
本文还就数控砂带磨削机床的安装和调试展开了讨论，并提出了安装和调试应注意的问题。
The installation of machine tools within the region, if the ground plane height difference over the adjustment range of this product, you can set the machine and load has increased by pads.
机床的安装区域内，如果地基平面的高度差超过本产品的调节范围时，可以在机床与负荷盘间增加垫片。
The experimental results showed that the high tenacity polyester filament can be obtained by partial innovation of the machine and process adjustment.
实验结果表明，通过对设备作局部改造并调整生产工艺，就可生产高强涤纶丝。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
NC machine speed adjustment, and more and more application of the VVVF technology to achieve.
数控机床的转速调整，目前越来越多地应用了变压变频技术来实现。
After the modification of step feed mechanism of deep drill combined machine tool, simplifying structure, convenient adjustment and reducing fault rate have been proved.
对深孔钻屑组合机床分级进给机构进行改进后，达到了简化结构、方便调整、减少故障的目的。
Suitable for all kinds of pouch machine. Automatically tracking rewinding speed and the speed of pound machine in operation without adjustment.
适合各类制袋机使用，收卷速度与制袋机速度自动追踪，运转中不用调整。
Under a traditional installation method a shafting is first mounted on a shipway and after a launching, the shafting undergoes an alignment through the adjustment of a main machine location.
传统的轴系安装方法是先在船台安装轴系，后下水通过调整主机位置进行轴系对中安装。
Under a traditional installation method a shafting is first mounted on a shipway and after a launching, the shafting undergoes an alignment through the adjustment of a main machine location.
传统的轴系安装方法是先在船台安装轴系，后下水通过调整主机位置进行轴系对中安装。
应用推荐