Adhesive joint, as an important method of joint, has been widely used in the construction.
粘接作为一种重要的连接方式，在结构加固中已经得到较广泛的应用。
Common methods of general conveyor belt mechanical joint fittings, cold adhesive joints, hot vulcanized joints.
一般输送带接头常用方法有机械接头、冷粘接接头、热硫化接头等。
Energy dispersive X-ray spectroscopy(EDX) is a kind of analysis method used in researching the adhesive joint and polymer composite surface and interface characters.
EDX是一种研究粘接接头和聚合物基复合材料表界面性能的分析测试方法。
For a given layered planar structure, we use the solidifying process of the adhesive layer to simulate the change process of interface strength of the adhesive joint.
对于给定的层状平面结构，将粘接层的固化过程用于模拟粘接层界面强度的变化过程。
According to the characteristics and requirements of the adhesive joint, the authors design and set up the testing platform of bonding strength for different materials.
根据粘接接头的特点和需要，自行设计和制造了异种材料粘接强度测试平台。
The results showed that the probabilistic model could reflect the real conditions of adhesive joint and provide reference for the probability design in adhesive structure.
结果表明，该模型可以有效地反映接头的实际情况，为粘接结构的可靠度设计提供了依据。
The reason of the failure of epoxy bonded joint in water was that the epoxy adhesive on the metal surface was substituted for water.
环氧胶接接头在水中破坏失效的原因主要是渗入到胶接层的水分子取代了胶粘剂分子在金属表面的粘附。
There should be no adhesive tape or plastic belt on the wall surface to avoid the formation of joint seepage.
朝墙面不得有粘胶带或塑料带的存在，避免形成结合部缝隙渗水。
The article introduces, as taking the measurement of sticking cracking-resistant adhesive tape at the joint between GRC boards, the cracks of the wall have been prevented effectively.
本文采用在GRC轻板的接缝处粘贴防裂带的措施有效地解决了墙体开裂。
The effect of elastic modulus of adhesive on the str ess distribution in aluminium alloy single lap joint was investigated using elastic-plastic finite element method(FEM).
运用弹塑性有限元法，研究了胶粘剂弹性模量对含间隙的铝合金单搭接接头上应力分布的影响。
An adhesive dike slot (31) is formed around the joint concave bottom, thus preventing the main body and the neck back side from dirtiness caused by excessive adhesive overflow.
粘合剂堤槽(31)形成在接合凹底部的周边，以防止用粘合剂连接时过量粘合剂溢出弄脏主体及琴颈的背面。
To evaluate the clinical value of arthroscopic release combined with hyaluronate sodium intraarticular injection for adhesive knee joint stiffness.
目的探讨关节镜下膝关节粘连松解结合透明质酸钠关节内注射对治疗膝关节粘连性强直的价值。
The failure form of joint, mechanical analysis of joint, joint design and test methods of adhesive bonding of composites are presented briefly in this paper.
本文简略叙述复合材料胶接的接头破坏形式，接头力学分析，接头设计及测试方法。
The utility model provides an improved mechanical sealed adhesive pipe joint, which takes the mechanical mode to seal and the adhesive mode to fix.
本实用新型提供一种改良的机械密封粘接式管接头。
The peel force of LWB joint is far greater than that of adhesive bonded joint.
激光胶接焊接头的抗剥离力远大于胶接接头的抗剥离力。
We offer two kinds of fiberglass joint tapes, sell-adhesive mesh tape and glass tissue tape.
我司可供应两种不同类型的嵌缝带，即自粘网格带和玻纤薄毡带。
Is a joint venture, was founded in 1990, the production of adhesive tape are professional manufacturers.
和顺胶粘带制品有限公司是一家合资企业，始建于1990年，是生产胶粘带的专业厂家。
On the other hand, the recessing in the joint with low elastic modulus adhesive caus es the peak stresses increase evidently that may decrease the nominal and actual strength of the joint markedly.
而对于低弹性模量胶粘剂接头，间隙使得接头上的应力峰值明显上升，可能导致接头的名义强度和实际强度显著降低。
The reason for reduction of bonding performance of epoxy bonded joint was the degradation of epoxy adhesive.
胶粘剂分子链的降解是环氧胶接接头胶接性能降低的主要原因。
Using FN-309 adhesive etc. as joint adhesive and, the water-resistant abrasive cloth, R/R or G/G abrasive cloth as the substrate belts the process of abrasive cloth lap jointing was studied.
以FN-309胶粘剂等为接头胶，耐水砂布、全树脂砂布和动物胶砂布等作材料，制作搭接砂带工艺的研究。
The BEM technique for adhesive-bonded structure proves valid by comparing the stress distribution for double lap joint calculated in this paper with that calculated by finite element method.
对双搭接接头进行了边界元应力分析，并和有限元结果进行了对比，从而证实本文方法的有效性。
Due to the extremely low temperatures, Habasit looked for a solution with a more flexible belt with textile tensile member and an adhesive-free joint.
由于极低的温度下，哈伯斯特看着了一个更灵活的皮带，纺织拉伸成员和胶粘剂自由联合的解决方案。
After the adhesive is solidified, the pipe and the pipe joint body are screwed into a whole through the screw plug.
待粘接剂固化后，管子、管接头体通过螺丝堵头凝接成一个整体。
The invention relates to a conveyer belt joint peeling device, in particular to a device which peels off each layer of adhesive tape of the conveyer belt.
本发明涉及一种运输带接头剥头装置，具体地说是剥开运输带的每一层胶带的装置。
The invention relates to a conveyer belt joint peeling device, in particular to a device which peels off each layer of adhesive tape of the conveyer belt.
本发明涉及一种运输带接头剥头装置，具体地说是剥开运输带的每一层胶带的装置。
应用推荐