A method is presented to calibrate the beam's direction.
提出了一种标定光束方向的方法。
A method is presented for determining the emittance of hot solids.
本文讨论一种确定固体材料比辐射率的方法。
A method is presented for knowledge verification based on a directed graph.
对于知识校验，提出一种基于有向图的知识校验方法。
In this paper a method is presented for solving Non-linear Eigenvalue problems.
对非线性特征值的求介本文提出了一种方法。
A method is presented to generate the mesh for wetted surface of floating body.
给出了一种浮体湿表面网格生成方法。
A method is presented for unmanned helicopter flight dynamics model identification.
研究了一种无人直升机飞行力学模型辨识方法。
A method is presented for calculation of air resistance in melt - spinning quench duct.
介绍纺丝吹风窗的阻力计算方法。
A method is presented for measuring semiconductor resistor using ratio sampling techniques.
介绍一种采用比值采样测量半导体温度电阻的测量方法。
A method is presented for studying bistatic scattering of acoustic waves by finite elastic target.
给出了水中有限长弹性目标声散射问题的求解方法。
A method is presented for assembly modeling of modular fixture with object Orient (o o) technology.
给出一个面向对象(O - O)的组合夹具装配建模方法。
A method is presented for assembly modeling of modular fixture with object Orient (O-O) technology.
给出一个面向对象(O - O)的组合夹具装配建模方法。
Then, a method is presented based on the singular value decomposition to compute the minimal norm solution.
然后用奇异值分解给出了求解最小范数解的一种方法。
Based on the Parabolic Radon transform, a method is presented for missing offset restoration in this paper.
本文简述了一种利用抛物线拉冬变换算法来实现空间插值的方法。
A method is presented for measuring the minority recombination Lifetime in MOS fet's by charge pumping effect.
本文介绍了应用电荷抽取效应测量MOS晶体管中少子复合寿命的方法。
A method is presented in the paper, with which leather area with irregular edge can be automatically measured.
本文提出了一种自动测量不规则皮板面积的方法。
A method is presented for converting the array representation of a binary image into the linear quadtree description.
本文提出一种方法实现二值图象的二元数组表示转换成线性四元树描述。
A method is presented for the measurement of integrated thermal neutron flux in a high flux reactor by a Co-activation method.
本文叙述了用钴活化法测定高通量堆中热中子积分通量的方法。
Based on the computer simulation technique of concrete mesostructure, a method is presented of computing the ITZ volume fraction.
根据混凝土细观结构模拟技术，提出了混凝土界面体积百分比的计算方法。
A method is presented for control parameters self-optimization of fuzzy controller in order to obtain a optimal fuzzy controller.
针对模糊控制器中的控制参数提出了一种自寻优方法，可获得一个基于一定性能指标的最优模糊控制器。
A method is presented for measuring the shear-wave attenuation of solids by using propagation of ultrasonic wave in a wedge block.
介绍了利用劈形楔块作波型变换，达到用纵波探头测量材料横波衰减系数的方法。
Furthermore, a method is presented to fill the gaps between paths and extend the endpoints of path trajectory to the surface boundary.
另外，对路径偏移中出现的缝隙给出了填补方法，并使偏移后的路径轨迹延伸至曲面边界。
Making use of the analogous relations between mechanics and electrical circuit, a method is presented to deal with linear discrete system.
根据力学系统与电学系统物理量间的对应关系，提出了用电路定律处理线性离散系统谐强迫振动的方法。
A method is presented to calculate automatically the best gray threshold, which is suitable for images under different scanning resolutions.
提出一种灰度阈值自动计算方法，适合于自动计算不同扫描分辨率下的图像的最佳灰度阈值。
Based on the conventional design methods of structural vibration, a method is presented to evaluate the reliability of structural vibration.
以传统的结构振动设计方法为基础，提出了一种进行振动可靠性设计的方法。
A method is presented here for the dynamic analysis of arch dams by means of vibration modes of one dimensional arch and cantilever elements.
本文将拱坝这样一种几何形状和边界条件都比较复杂的壳体结构划分为梁拱两组子结构，利用它们的一维模态建立动力方程求解振动问题。
After the shortcomings of existing methods for determining the index weight are analyzed, a method is presented on the basis of the worst scheme.
简要分析目前指标赋权法的优缺点，给出了一种利用最劣方案计算指标权重的方法。
A method is presented for use in establishing probability model of seismic intensity attenuation in regions with abundant data of isoseismal maps.
本文在考虑地震烈度评定和预测的不确定性的基础上，提出建立烈度衰减概率模型的方法。
A method is presented, which makes it possible to calculate velocity and interface depth of the reflected wave in a vertically inhomogeneous medium.
本文提出了一种利用反射波走时曲线计算垂向非均匀介质速度和反射界面深度的方法。
After analyzing the shortcoming of existing methods on determining the index weight, a method is presented on the basis of ideal optimization scheme.
简要分析当前指标赋权法的优缺点，给出一种利用理想最优方案计算指标权重的方法。
A method is presented by using computational geometry techniques to determine optimal tool position and orientation for 5-axis machining with torus end-mill.
应用计算几何技术来决定优化的刀具定位和刀具姿态以实现环形刀的5轴自由曲面数控加工。
应用推荐