介绍了平衡式复合齿轮泵结构原理。
The construction and principle of the balanced compound gear pump is introduced.
我在向两位印度客人介绍齿轮泵。
这是起重机配件液压齿轮泵。
我们沉着症者齿轮泵系列多字符串选项。
Multiple string option with our IPH series inscribed gear pump.
齿轮泵的旋转方向要与进、出油口相符。
Gear pump with the direction of rotation into and out in line with the oil mouth.
齿轮泵如何选择密封垫？
氨液循环泵由齿轮泵改为高速泵，效果较好。
Using high speed pumps to replace gear pumps for ammonia recycling, satisfactory results were achieved.
研制了一个内燃机车用齿轮泵的CAD系统。
高粘度齿轮泵并不能产生压力，它只是输出流量。
High viscosity gear pump does not generate pressure, it is only the output flow.
本文对齿轮泵和液压缸的出现的常见故障进行分析。
This article counter gear pump and hydraulic cylinder's appearance's common breakdown carries on the analysis.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
到目前，国内齿轮泵市场产能大致为450万件左右。
Up to now, the domestic market capacity gear pump roughly 450 million pieces.
本文从理论上推导出齿轮泵长圆形卸荷槽的设计计算公式。
This paper derives theoretically calculation formula of designing circle-form-at-ends rectangle unloading groove.
止回阀与安全阀在齿轮泵的输出管路上最好安装一个止回阀。
Check valve and relief valve on the output of the gear pump tube had better install a check valve.
介绍了熔体齿轮泵在塑料挤出成型及微孔塑料加工中的应用。
The applications of polymer melt gear pump in plastics extrusion and microcellular plastics forming are introduced.
同步齿轮泵能够降低齿轮泵径向力，提高齿轮泵的工作压力。
The synchronization gear pump can reduce the radial and boost the work pressure.
本文介绍了内啮合齿轮泵齿轮设计的准则及应注意的几个问题。
This paper introduces the criterion and some noted problems of gear design for internal gear pump.
紧固齿轮泵、电动机的地脚螺钉时，螺钉受力应均匀，连接可靠。
Retention gear pump, motor and foot screws, screw the force should be uniform, reliable connection.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
这两种内啮合齿轮泵的工作原理和外啮合齿轮泵的工作原理相同。
These two kinds of internal gear pump working principle and external gear pump working principle the same.
齿轮泵主动轴与衬套磨损后，其配合间隙增大，必将影响泵油量。
Pump drive shaft and bushing wear, the tolerance clearance increases, will affect oil pump.
研究结果表明，平衡式复合齿轮泵的流量脉动较普通齿轮泵要小得多。
The result is that the flow pulsation of the pump is far smaller than that of the same type.
与柱塞泵、单螺杆泵及齿轮泵不同的是，单螺杆泵可用于药剂填充和计量。
With the piston pump, diaphragm and gear pumps is different is that single-screw pump can be used for pharmaceutical filling and measurement.
本文在分析齿轮泵的流量脉动和压力脉动的基础上，设计出一种错齿齿轮泵。
The interlaced gear pump is designed on the basis of analysing flow and pressure pulses.
随著齿轮啮合重合系数的减小，齿轮泵的流量增大，困油容积和流量脉动率减小。
If the coefficient of engagement overlap decreases, the flow aggrandize, trapping volume and the flow pulsating ratio decreases.
困油现象是由齿轮泵自身工作原理造成的，它直接影响着齿轮泵的工作性能及寿命。
The phenomenon of oil-trap stems from the principle of gear pumps, and it affects directly the performance and life of the gear pumps.
齿轮泵密封垫的选用原则是，对于要求不高的场合，可凭经验选取，不合适时再更换。
The gear pump seals the selection principle is not high demand, for the occasion, but by experience, not to replace timely selection.
该泵摆脱了传统设计的束缚，使得齿轮泵在设计、生产和使用上进入了一个新的领域。
The pump out of the shackles of traditional design, making gear pump in the design, production and use into a new area.
对比渐开线齿轮泵，单圆弧齿轮泵的瞬时排量与齿轮角速度成正比，且稳定，无脉动。
Comparing with involute gear pump, the instant displacement is in direct proportion to the angular velocity of the gear and stable without pulsation.
合理确定齿轮泵的工作转速，使齿轮与轴的转动避开啮合共振频率，可以防止噪声加剧。
Rationally define the work gear pump speed, gear and the axis of rotation to avoid engaging resonance frequency, can prevent noise intensified.
应用推荐