这些驱动器，中央螺旋桨轴通过减少锥齿轮2：1减少。
These drive the central propeller shaft through bevel reduction gears with a 2:1 reduction.
密封空气被注入到主马达轴（顶部和下部）和驱动马达的齿轮轴的迷宫式密封里。
Seal air is injected into the labyrinth seals located at the main motor shaft (top and bottom) and at the pinion shaft driving the motor.
齿轮A位于驱动轴的末端，齿轮b在副传动轴上，它们恒定啮合。
Gear a, at the end of the drive shaft, and gear B, on the countershaft, are in constant mesh.
齿轮段也有输入轴和输出轴，它必须吧动力传递给驱动轮。
The gear section also has the input shaft and the output shaft needed to transmit power to the drive wheels.
发电齿轮箱的外壳包覆驱动轴。
The casing of the electricity generating gear box covers the driving shaft.
两个半轴齿轮的加速和减速从而实现了两个驱动轮之间的差速。
This speeding up and slowing down of the side gears allows differential speeds at the drive wheels.
也就是说，驱动力是从传动轴末端的传动齿轮输送到差速器的。
The driving power enters the differential through the drive pinion on the end of the propeller shaft.
功率经过主动齿轮、从动锥齿轮、壳体和行星齿轮轴来到行星齿轮，然后功率被均分，送到半轴齿轮、半轴，最后到达驱动轮。
Power flows through the drive pinion, ring gear, case, and pinion shaft to the differential pinions. Then power splits equally and goes to the side gears, axle shafts, and drive wheels.
这样，普通织机应具备两根轴，主轴驱动筘座并通过齿轮驱动另一根轴。
The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.
在自行车驱动轴上设置一个发电齿轮箱。
The bicycle driving shaft is provided with an electricity generating gear box.
驱动装置采用轴装式齿轮减速机与主动滚轮直联传动，结构紧凑，机械效率髙。
Driving device uses shaft type reduction device directly connected to capstan idler, its construct is compact and mechanical efficiency is higher.
第一个齿轮即主动轮的回转引起第二个齿轮即从动轮的回转。驱动轴通常连接到泵上面的齿轮上。
Rotation of one gear, the driver causes the second, or follower gear, to turn. The driving shaft is usually connected to the upper gear of the pump.
此时，使扶起驱动轴(46)的花键部花键嵌合在内置于扶起齿轮箱(71)中的扶起侧伞齿轮(83)的花键孔中。
In this case, the spline part of a raising driving shaft (46) is spline-fitted to the spline hole of a raising side bevel gear (83) built in a raising gear case (71).
二是将喷油泵与驱动齿轮间的连接方式改用法兰来连接，避免了由于轴的加工误差和安装同轴度的影响。
Another one is to connect the injection pump to the driving gear with flange to avoid the influence from machining error of shaft and coaxial degree while installing.
这样，普通织机应具备两根轴，主轴驱动筘座，并通过齿轮驱动另一根轴。
Thus a normal loom has two shafts. The main shaft drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.
与张力辊齿轮啮 合的小齿轮驱动传动轴；
The pinion meshed with the tension roll drives the transmission shaft;
与张力辊齿轮啮 合的小齿轮驱动传动轴；
The pinion meshed with the tension roll drives the transmission shaft;
应用推荐