这个预热的阶段通常被称为“预热方法的缓存 ”。
This warmup phase is effectively known as "warming up the method cache".
本文经过实验，从实践和理论上，研究了预热方法对消除夹送辊堆焊冷裂纹和热裂纹的影响。
Through experiment from reason and practice, the influence of the preheating method on eliminating crack of pinch roller in the surfacing welding was discussed .
现在大多数都是采用给发动机安装预热塞的方法来缩短启动时间的。
Now, most of them are used to shorten the starting time of the engine with the method of installing the preheating plug.
可选地，省时省力的方法是治愈染料在烘箱中预热至285度进行10分钟的水在烤箱以提供蒸汽的底的锅。
Alternatively, the time-saving method is to cure the dye in an oven pre-heated to 285 degrees for 10 minutes with a pan of water in the bottom of the oven to provide steam.
该方法为热管空气预热器的合理设计和安全经济运行提供了参考。
It provides reference for the reasonable design, the safety and economical operation of heat-pipe air preheater.
将要介绍的这些方法为：增加黑液固形物含量、空气预热、吹灰系统、给水预热、蒸汽参数和电除尘后的热回收。
The methods to be presented are: increased dry solids content of black liquor, air preheating, soot blowing arrangement, feedwater preheating, steam parameters and heat recovery after precipitator.
分析影响柴油机低温起动的因素，提出利用燃油加热器为柴油机低温预热起动的具体方案，并提供加热器功率的计算方法。
Main elements impacting diesel cold starting are analyzed, concrete plan for diesel cold preheating and starting is put forword, that is using fuel oil heater.
采用工业试验的方法对两台分别燃油及燃煤的电站锅炉的热管式空气预热器灰污系数的确定进行了分析和研究。
Determination of fouling factors of heat pipe air preheaters for two utility boilers burning oil and coal respectively are implemented through industrial experiments.
同时总结了一套计算焊接预热温度确定方法和焊接接头匹配的选取原则与方法。
In addition, a calculating method on welding preheating temperature and a selective principle and method on welding component matching are concluded.
通过优化工艺参数、机体预热的方法可以提高模具修复质量。
The repairing quality of the dies was achieved by optimum parameter of laser cladding and preheating.
本文将要介绍的方法为：增加黑液固含量、空气预热、吹灰系统、给水预热、蒸汽参数和电除尘后的热回收。
The methods to be presented are: increased dry solids content of black liquor, air preheating, soot blowing arrangement, feed water preheating, steam parameters and heat recovery after precipitator.
提出了正确使用、维护预热器的方法。
Also involved is how to operate and maintain the preheater appropriately.
与电阻焙烧相比，热焙烧提供了更好的预热控制，因此热焙烧是很好的预热铝电解槽的方法。
Compared with electric resistance bake-out, thermal bake-out provides better preheating control, so thermal bake-out is a kind of very good method for preheating aluminum reduction cells.
通过模拟实验的测试，此方法对水泥回转窑旋风预热器的控制起到了很好的效果。
After stimulant experiment testing, this method Plays a good effect in the Cement kiln preheater control.
本文简述采用机械清洗方法替代化学清洗方法清洗真空制盐预热器中垢层。并在实际应用中取得良好效果。
This paper describes mechanical cleaning in place of chemical cleaning to clean the scale in vacuum salt making pre-heater with good results in practical application.
将含三氯乙醛废硫酸加水稀释后，不需预热，直接向废硫酸中通入水蒸汽进行蒸馏的方法处理含三氯乙醛废硫酸。
The waste sulfuric acid containing chloral was treated with new process, including diluted with water and directly steam distillating without pre-heating.
这种方法简单易做，是一种很好的大脑预热运动。
This one is easy to do at home and easy to get your brain warmed up.
根据空气预热器冷端壁温的要求，提出了冷风预热的方法以及暖风器选择的原则。
Depending upon the requirements of cold end temperature of tube wall of air preheaters, the method of cold air preheating and the criterion of selection for air heater are put forward.
为此，探讨了煤粉预热喷吹对混合煤粉爆炸性的影响，以期为强化喷煤燃烧提供一种新的有效工艺方法。
The effect of the preheated mixed pulverized coal on its explosiveness is discussed, and the aim is to provide a new effective technique for reinforcement combustion of the pulverized coal.
对预热器、分解炉、热风管道附属设备的结构尺寸、计算公式、改进方法等方面作了详细阐述。
This paper details structure dimensions, calculation formulas, improvement approaches etc. for preheater, precalciner, hot gas pipes and their subsidiary devices.
采用碱性药皮焊条和焊前接头预热的施焊方法，焊接的空间管道接头热应力小。
For overhead pipeline, welding with basic-compound coated electrodes and pre-welding heating of the joint will reduce the joint thermal -stress.
该方法不仅有足够的传热计算精度，更适于三分仓空气预热器的积灰状态在线实时监测。
Not only the method has enough precision for heat balance calculation but also it is fit for the online monitor of the fouling status.
然后，本文通过正交试验的方法研究了压射速度、浇注温度和模具预热温度对铸件缩松缩孔缺陷的影响。
By use of orthogonal test design, how the injection speed, pouring temperature and mold temperature effects the casting shrinkage porosity forming is studied.
分析影响柴油机低温起动的因素，提出利用燃油加热器为柴油机低温预热起动的具体方案，并提供加热器功率的计算方法。
This article has described a high efficient and energy saving heating device-fuel oil hot air oven, which is used as the oven in baking line of painting production line.
通过采取焊前预热、控制焊接线能量和层间温度、焊后保温缓冷等工艺措施，并采用相应的检测方法，保证了胺液吸收塔的低温焊接质量。
According to the test, the welding interlayer temperature of X60 pipeline in the normal and low temperature is analyzed in order to study the influence of its variable range on welding quality.
通过采取焊前预热、控制焊接线能量和层间温度、焊后保温缓冷等工艺措施，并采用相应的检测方法，保证了胺液吸收塔的低温焊接质量。
According to the test, the welding interlayer temperature of X60 pipeline in the normal and low temperature is analyzed in order to study the influence of its variable range on welding quality.
应用推荐